background image

Page 7

For technical questions, please call 1-800-444-3353.

Item 69576 

        

Initial Tool Set Up/Assembly

  Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this 

manual including all text under subheadings therein before set up or use of this product.

Note:

 For additional information regarding the parts listed in the following pages, 

refer to the Assembly Diagram near the end of this manual.

Note:

 This air tool may be shipped with a protective plug covering the air inlet.  Remove this plug before set up.

Air Supply

TO PREVENT SERIOUS INJURY FROM EXPLOSION: 

Use only clean, dry, regulated, compressed air to power this tool.   

Do not use oxygen, carbon dioxide, combustible gases,  

or any other bottled gas as a power source for this tool.

1.  Incorporate a filter, regulator with pressure gauge, 

oiler, in-line shutoff valve, and quick coupler for 

best service, as shown on Figure B on page 8 

and Figure C on page 9. 

 An in-line shutoff 

ball valve is an important safety device because 

it controls the air supply even if the air hose 

is ruptured.  The shutoff valve should be a 

ball valve because it can be closed quickly.

Note: 

If an automatic oiler system is not used, 

add a few drops of Pneumatic Tool Oil to the airline 

connection before operation.  Add a few more drops 

after each hour of continual use.

2.  Attach an air hose to the compressor's air outlet.  

Connect the air hose to the air inlet of the tool.  

Other components, such as a coupler plug 

and quick coupler, will make operation 

more efficient, but are not required.

WARNING!  TO PREVENT SERIOUS INJURY 

FROM ACCIDENTAL OPERATION: 

Do not install a female quick coupler on the tool.

  

Such a coupler contains an air valve that will 

allow the air tool to retain pressure and operate 

accidentally after the air supply is disconnected.

Note: 

Air flow, and therefore tool performance, 

can be hindered by undersized air supply components.  

The air hose must be long enough to reach 

the work area with enough extra length to 

allow free movement while working.

3.  Turn the tool's throttle or switch to the off position; 

refer to Operation section for description of controls.

4.  Close the in-line shutoff valve between 

the compressor and the tool.

5.  Turn on the air compressor according to 

the manufacturer's directions and allow it 

to build up pressure until it cycles off.

6.  Adjust the air compressor's output regulator 

so that the air output is enough to properly 

power the tool, but the output will not exceed 

the tool's maximum air pressure at any time.  

Adjust the pressure gradually, while checking the 

air output gauge to set the right pressure range.

7.  Inspect the air connections for leaks.  

Repair any leaks found.

8.  If the tool will not be used at this time, turn off 

and detach the air supply, safely discharge 

any residual air pressure, and release 

the throttle and/or turn the switch to its off 

position to prevent accidental operation.

Note:

 Residual air pressure should not be present 

after the tool is disconnected from the air supply.  

However, it is a good safety measure to attempt to 

discharge the tool in a safe fashion after disconnecting 

to ensure that the tool is disconnected and not powered.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 69576

















Отзывы: