Central Machinery 96500 Скачать руководство пользователя страница 11

Page 11

SKU 96500

for technical questions, please call 1-800-444-3353.

symptom

probable cause

possible remedy

Engine stops suddenly.

1.  Gas tank empty.
2.  Carburetor clogged
3.  Floater is leaking.
4.  Needle valve sticks.
5.  Spark plug dirty or damaged.
6.  Spark plug connector wire 
damaged or disconnected.
7.  Low oil auto-shutdown.
8.  Ignition coil damaged.
9.  Cylinder or valve damaged.

1.  Fill gas tank.
2.  Clean carburetor and check 
fuel line.
3.  Repair or replace.
4.  Disassemble floater chamber 
and clean.
5.  Replace spark plug.
6.  Check and repair spark plug 
wire.
7.  Fill with oil.
8.  Repair or replace.
9.  Disassemble, check, and 
repair.

engine excessively hot

symptom

probable cause

possible remedy

Engine runs excessively 
hot.

1.  Ignition timing off.
2.  Engine oil low.
3.  Exhaust pipe or muffler 
clogged.
4.  Flow guard is leaking.
5.  Cooling fan loose, damaged, 
or clogged.
6.  Cylinder, piston, or piston 
ring is worn resulting in air flow 
between cylinder and crankcase.
7.  Engine speed maximum set 
too high.
8.  Crankshaft main bearing burnt.

1.  Adjust ignition advance angle.
2.  Fill with oil.
3.  Clean out exhaust pipe and 
muffler.
4.  Repair leakage.
5.  Clean, repair, or replace fan. 
6.  Replace damaged parts. 
7.  Re-adjust engine speed 
governor.
8.  Replace main bearing.

Abnormal engine noise

symptom

probable cause

possible remedy

Noise of piston banging, or 
other metal-on-metal

1.  Piston, piston ring, or cylinder 
worn.
2.  Tie rod, piston pin and hole 
worn.
3.  Crankshaft main bearing worn.
4.  Piston ring broken.
5.  Carbon deposits in combustion 
chamber.
6.  Spark plug gap too small.
7.  Using wrong gasoline.
8.  Engine running too hot.
9.  Incorrect valve clearance.
10.  Flywheel not tightly 
connected to crankshaft.

1.  Replace worn parts.
2.  Replace worn parts.
3.  Replace main bearing.
4.  Replace piston ring.
5.  Clean combustion chamber.
6.  Adjust electrode clearance.
7.  Empty gas tank and refill with 
proper gasoline.
8.  See Troubleshooting 
Excessively Hot Engine.
9.  Readjust valve clearance.
10.  Retighten flywheel.

Содержание 96500





















Отзывы: