Central Machinery 90589 Скачать руководство пользователя страница 1

Страница: 1 / 32

TIRE CHANGER

SEMI-AUTOMATIC WITH SWINGING ARM

Model

90589

ASSEMbly ANd OpERATING INSTRUCTIONS

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAl.

2003 by Harbor Freight Tools

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual revised 07g

Содержание 90589

































Результаты поиска

Содержание 90589

Отзывы:

Похожие инструкции для 90589

Бренды по названию

Популярные бренды

Central Machinery 90589, Руководство по сборке и эксплуатации

Результаты поиска

Содержание 90589

Отзывы:

Похожие инструкции для 90589

Бренды по названию

Популярные бренды