background image

Page 10

For technical questions, please call 1‑800‑444‑3353.

SKU  68150        

7.  To prevent accidents, turn off the 

tool and disconnect its power supply 

after use.  Clean, then store the tool 

indoors out of children’s reach.

MAINTENANCE AND 

SERVICING

  Procedures not specifically 

explained in this manual 

must be performed only by 

a qualified technician.

NOTE: The Demolition Hammer will 

cease operation once Carbon 

Brushes are worn.  Check 

Brushes every 100 hours and, 

when necessary, replace them.

 

TO PREVENT 

SERIOUS INJURY 

FROM ACCIDENTAL 

OPERATION: Release the Trigger 

Switch and unplug the tool from 

its electrical outlet before 

performing any inspection, 

maintenance, or cleaning 

procedures.
TO PREVENT SERIOUS INJURY 

FROM TOOL FAILURE: 

Do not use damaged equipment.  

If abnormal noise or vibration 

occurs, have the problem 

corrected before further use.

Maintenance, and Lubrication

1. 

BEFORE EACH USE,

 inspect the 

general condition of the tool.  Check 

for loose hardware, misalignment 

or binding of moving parts, cracked 

or broken parts, damaged electrical 

wiring, and any other condition that 

may affect its safe operation.

2. 

AFTER USE,

 wipe external surfaces 

of the tool with clean cloth.

3.  Wipe tool with a lint-free cloth 

after each use to remove all 

dust and grit from the tool.

NOTE: The Demolition Hammer has an 

air‑tight construction, allowing for 

three months of continuous usage 

before lubrication is needed.

4.  Check the Oil Gauge (61) located 

on the underside of the housing.

5.  If oil is low, remove the Oil Plug 

(56A) and use the Oil Bottle 

(904) to fill tool with 1-1/3 ounces 

of Rotella #40 Engine Oil.

6.  Replace the Oil Plug.
7.  Examine the tool before each use.  Make 

sure the Chisel is sharp and not dull 

or cracked.  Replace worn or broken 

Chisels with approved replacement 

Chisels from Harbor Freight Tools.

8.  Check that all mounting screws are 

tightened. Retighten any loose screws.

9.  Store in temperatures no 

lower than 50-60° F.

10. 

WARNING!  If the supply cord 

of this power tool is damaged, 

it must be replaced only by a 

qualified service technician.

Replacing Carbon Brushes

NOTE: The Demolition Hammer will 

cease operation once Carbon 

Brushes are worn.  Check Brushes 

every 100‑120 hours and, when 

necessary, replace them.

1.  Use screwdriver to remove 

the Carbon Brush Cover (69). 

See Figure 1 on page 8.

Содержание 68150















Отзывы: