background image

Page 8

SKU 43353

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

3.

Replace the Hex Head Screws (57).

Adjustment of the Lower Cutting Blade (23)

1.

Turn the Handle Arm (18) and lower the upper Blade (23) to its lowest position.

2.

Loosen the two inset Hex Head Screws (58) located on top of the Cutter Table (2).

3.

Adjust the lower cutting Blade (23) by turning its Adjusting Bolts (17).

The distance between the lower and upper cutting Blade (23) should be 5 to 8 percent

of the thickness of the workpiece.

4.

Tighten the two inset Hex Head Screws (58) located on top of the Cutter Table (2).

Installation and Adjustment of the Backstop (21)

1.

Screw the two Support Rods (19) into the back of the Crossbeam (3).

2.

Slide the two Support Blocks (20) onto the Support Rods.

3.

Attach the Backstop (21) to the Support Blocks using the Hex Head Screws (42).

- If used for bending, attach the Backstop on top of the Support Blocks.

- If used for shearing, attach the Backstop on the bottom of the Support Blocks.

4.

Adjust the Backstop to the desired depth and tighten the Knob (41).

Maintenance

1.

Before using this machine, certain parts coated with rust inhibitor must be first cleaned

using varnish thinner.

2.

Lubricate the eccentric mechanism daily with machine oil.

3.

Periodically check all nuts, bolts, and screws for tightness.

4.

Periodically lubricate the rollers surface with a clean rag and machine oil.

5.

Place the Cover over the rollers when not in use.

Содержание 43353












Отзывы: