Central Machinery 34951 Скачать руководство пользователя страница 8

Страница: 8 / 12

Page 8

For technical questions, please call 1-800-444-3353.

SKU 34951

assemBlY

The Belt Sander is shipped almost

completely assembled. The major items to

be attached are the disc table (58), the belt

table (31), and the sanding belt (6). (These

numbers refer to the assembly diagram

and parts list at the back of this manual.)

We will refer to the tall part of the sander

angled toward you as the front. The “on/

off” switch is to your right.

Belt table assembly

Get out the table (31), 16mm screw

(36), No. 8 washer (2), locking nut

(32), knob (33), spring (34), and

screw (36).
Remove the cover (3) by removing

the securing knob (1) and lifting up.
The screw (36) goes on the inside;

the other pieces are installed from

the outside. The washer goes closer

to the table, then the locking nut,

followed by the knob, spring, and

finally the last screw.

The knob is used to lock the table in

place when adjusting the angle.
Do not replace the cover until the belt

has been installed. This is covered

below.

Disc assembly

Remove the cover (50).

Remove the dust collector

(59).

Stick the sanding disc on the disc

wheel (53).

Get the disc wheel to the shaft of

the motor with the hex head bolt

(52).
Replace the cover and dust

collector.

Disc table assembly

Get out the table (58),4 x 22 pins

(60), the No. 6 washers (55), and the

wing nuts (61).
Attach the table to the cover using

the wing nuts and washers.
Drive in the pins so that the table can

“swing” for tilting.

miter

gauge assembly

Get out the shaft (57), scale (56), No.

6 washer (55), and fastening knob

(54).
Attach scale to shaft with washer and

knob.

installing anD remOVing

sanDing Belts

UNPLUG THE MACHINE FROM

THE POWER SOURCE.
Unless it has already be taken off,

remove the knob (1) from the top

of the sander. Remove the side

cover (3).
Put the belt over the upper wheel

(8) and large belt wheel (29).
Lift up on the belt tracking knob

(19) and slide the belt over the

lower belt wheel.
Replace the cover.

Brought To You By Augusta Flint

Содержание 34951













Результаты поиска

Содержание 34951

Отзывы:

Похожие инструкции для 34951

Бренды по названию

Популярные бренды

Central Machinery 34951, Руководство по установке и эксплуатации

Результаты поиска

Содержание 34951

Отзывы:

Похожие инструкции для 34951

Бренды по названию

Популярные бренды