Gateway Instruction Manual
Page 9
Warning
: The cover must be closed, clasped, and screwed/fastened shut with the
supplied screws/fastener to prevent access to live circuits.
Avertissement
: La couverture doit être fermée, fermée et serrée et a vissé/attaché
fermé avec les vis/attachefournies pour prévenir l'accès pour vivre des circuits.
3.5 Setup
Prior to applying power, the Gateway must be added to the Data Center (including
adding the Gateway and Monitor serial numbers into the database).
3.5.1
Cellular Gateway Setup
There are no extra cables for the Cell Gateway.
If your cellular modem was not factory provisioned or activated on a network then
follow the special instructions located in the appendix under Advanced Setup.
3.5.2
Ethernet Gateway Setup
Using an Ethernet cable, connect the Controller to a port on a network switch or
hub or any standard RJ-45 network jack where a computer could gain access to the
Internet. Longer Ethernet cables may be used, if necessary, but the total cable
length includingpermanent wiring inside the building should not exceed 300 feet.
The Gateway will connect only to the Data Center and no inbound port forwarding
rules should be required on the customer’s network firewall.
If the local network requires a static IP address,then follow the special instructions
located in the appendix under Advanced Setup
.
3.6 Activation
Following wiring and setting up the Gateway, the unit can be activated by turning on
the supply power. When power is applied, the Gateway will enter a short test mode
and the two lights on the front of the housing will cycle from off to the color Yellow.
The Gateway will then enter an initialization phase, which may take several
minutes, during which time
Data Center
light will blink Yellow or Green. Once the
Gateway has communicated with the Data Center, it will enter normal operating
mode and the
Data Center
light will turn solid Green. The status indicator lights can
be interpreted as follows:
Caution
: Risk of Explosion if battery is replaced by
an incorrect type.Dispose of used batteries
according to the instructions.
Prudence
: Le Risque d'Explosion si la batterie est
remplacée par un type incorrect. Débarrassez-vous
des batteries utilisées selon les instructions.
Gateway Instruction Manual
Page 10
The
Data Center
light indicates Data Center communication status. The
Data
Center
light blinks approximately once per second any time Gateway is
powered.
Blinking Red – Network connection failure. (No network connection or
Loss of connection).
Blinking Yellow – System is connected to the network, but is waiting for a
response from network router or ISP. (Waiting for network)
Solid Yellow - System is starting up or connecting to the network. (Network
not ready)
Blinking Green – Connected to the network, but the Data Center has not
responded. (Waiting for Data Center to reply)
Solid Green – Connected to the network and talking to the Data Center.
(Normal operation)
The
MONITOR
light provides information about radio communication between
the Monitor and Gateway. The
MONITOR
light is normally “off”. It blinks only
when the Gateway is receiving radio transmissions.
Blinking Green – Data received from a valid Monitor.
Blinking Yellow – Some data was received from a valid Monitor but the
signal was weak or partially corrupt.
Move the Gateway or Monitor and
retest until the Monitor light blinks green.
Blinking Red – Radio signals were received from an invalid source.
4
Service and Technical Support
If you experience trouble with this equipment, please contact your distributor.
CAUTION
: The manufacturer does not support field changes or modifications to
any of the Level Monitoring System equipment unless they are specifically covered
in this manual. Any other modification to the equipment will void the manufacturer’s
warranty.
PRUDENCE
: Le fabricant ne soutient des changements de terrain ou des
modifications à aucun des équipements de Système de surveillance de Niveau à
moins qu'ils ne soient spécifiquement couverts dans ce manuel. Autre modification
à l'équipement va le vide la garantie du fabricant.
Warning
: This unit is to be serviced by qualified service personnel only.
Avertissement
: Cette unité doit être assurée l'entretien par le personnel de service
qualifié seulement.
