CEN-TECH 62120 Скачать руководство пользователя страница 27

Страница: 27 / 40

Page 27

For technical questions, please call 1-888-866-5797.

Item 62120

Custom Data Set - Record Select PIDs (continued)

6. After the passenger determines

that recording is finished, stop

driving. Data can be viewed

immediately or saved to view later.

Record Data

Recording Done!

Playback data?

YES

Figure AX

7. Interpret data according to

“Playback Data” on page 25.

Note:

If necessary, have a qualified

technician interpret the data.

Playback Live PID Data

This section contains advanced

functions. Some data may need to be

interpreted by a qualified technician.

1. From

Diagnostic Menu

, select

Live Data

, then press

OK.

Diagnostic Menu 3/11

Read Codes

View Freeze Frame

I/M Readiness

02 Monitor Test

On-Board Mon. Test

Erase Codes

Live Data

Figure AY

2. From

Live Data

, select

Playback Data

, then press

OK.

……………… .

Live Data

3/3

View Data

Record Data

Playback Data

Figure AZ

3. From

Select Memory,

select a

memory location marked with an

asterisk (*), then press

OK.

…………….

Select Memory 1/3

Location #1 *

Location #2
Location #3 ?

Figure BA

4. Interpret data according to

“Playback Data” on page 25.

Note:

If necessary, have a qualified

technician Interpret the data.

Содержание 62120









































Результаты поиска

Содержание 62120

Отзывы:

Похожие инструкции для 62120

Бренды по названию

Популярные бренды

CEN-TECH 62120, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 62120

Отзывы:

Похожие инструкции для 62120

Бренды по названию

Популярные бренды