CEN-TECH 62120 Скачать руководство пользователя страница 12

Страница: 12 / 40

Page 12

For technical questions, please call 1-888-866-5797.

Item 62120

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

TO PREVENT SERIOUS INJURY AND DEATH:

Exhaust gases are poisonous. Operate the vehicle in a well ventilated work area.

Wear ANSI-approved safety goggles during use.

Connect Scan Tool

CAUTION:

Do not connect or disconnect

the Scan Tool while the ignition

is on or the engine is running.
Note:

The Scan Tool is powered

by the vehicle’s battery.
1. Turn the engine and ignition

OFF.

2. Connect the OBD II Cable

to the Scan Tool.

3. Connect the other end of the

Cable to the 16-cavity DLC.
The DLC is normally located under

the dashboard on the driver’s

side. (Refer to vehicle’s owner’s

manual for location of DLC.)

Figure D: DLC

4. Turn the vehicle’s ignition

with the engine

OFF

Note:

Linking Error!

message

displays:

• Press the

ESC

button

• Verify the ignition is

• Verify the vehicle is OBD II compliant

5. If the message does not go away,

have the Scan Tool inspected

by a qualified technician.

Note:

To quick-check Emissions

Test Readiness, see

page 17.

Note:

To read Diagnostic Trouble

Codes, see

page 19.

Содержание 62120









































Результаты поиска

Содержание 62120

Отзывы:

Похожие инструкции для 62120

Бренды по названию

Популярные бренды

CEN-TECH 62120, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 62120

Отзывы:

Похожие инструкции для 62120

Бренды по названию

Популярные бренды