Cembre B1350-C, Руководство по эксплуатации, Страница: 9 / 48

9
ENGLISH
B1350
13AB485
RESET
SW:S1J41413
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-29000

BATTERY
3 SEC.
ERROR
001
30001

BATTERY






F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi


002


003


BATTERY
 
004


LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY BATTERY


min.
P
m
= 692 bar
Pp = 522.3 bar
Do not apply pressure to or stab at the touch button, a light touch using a bare finger is
sufficient. The command pulse is sent when the finger releases the button.
2.8) Battery status
The battery is equipped with LED indicators that indicate the remaining battery life at any time
by pressing the adjacent button (P) (Ref. to Fig. 5):
4 LEDs illuminated: fully charged
2 LEDs illuminated: 50 % capacity
1 LED flashing: minimum charge, replace the battery.
With the battery inserted into the tool, the remaining
battery life can also be checked on the display, via touch
button selection (Ref. to § 4).
The screen shown alongside indicates that the battery voltage has
dropped below a minimum safety threshold; under these conditions
the tool will not start,and it is necessary to recharge or replace the bat
tery. The approximate time to fully recharge a battery is about 100 miutes.
After each working cycle, and after the extraction of the battery from the tool, an integrated
battery cut-off device will operate after 70 s approx.
Then the LED nearest to button (P) will flash 5 times each 14 s approx. The battery will be
reactivated when it is reintroduced into the tool and the operating button is pressed.
2.9) Using the battery charger
Carefully follow the instructions in the battery charger user manual.
3. MAINTENANCE
The tool is robust, completely sealed, and requires very little daily maintenance. Compliance with
the following points, should help to maintain its optimum performance:
3.1) Thorough cleaning
Dust, sand and dirt are a danger for any hydraulic device.
Every day, after use, the tool must be wiped with a clean cloth taking care to remove any residue,
especially close to pivots and moveable parts.
Do not use hydrocarbons to clean the rubber parts.
3.2) Storage case
(Ref. to Fig. 8)
When not in use, the tool should be stored and transported in the plastic case, to prevent damage.
The case, type VAL P39, is suitable for storing the tool, the accessories and up to 8 die sets and pre-
prepared compression connectors.
VAL P39: Size 520x432x126 mm (20.5x17.0x5.0 inches). Weight 2,6 kg (5.7 lbs).
B1350
13AB485
RESET
SW:S1J41413
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-29000

BATTERY
3 SEC.
ERROR
001
30001

BATTERY






F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi


002


003


BATTERY
 
004


LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY BATTERY


min.
P
m
= 692 bar
Pp = 522.3 bar
B1350
13AB485
RESET
SW:S1J41413
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-29000

BATTERY
3 SEC.
ERROR
001
30001

BATTERY






F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi


002


003


BATTERY
 
004


LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY BATTERY


min.
P
m
= 692 bar
Pp = 522.3 bar