CellSecure E12 CLEO Скачать руководство пользователя страница 9

 

 

9

  Each time the E12 receives a panic signal; it will reset the siren timer and resend 

the Panic SMS. 

  The name of the person who activated Panic will be included in the SMS. 

  The siren can be stopped before the 4 minutes is up by switching to Off Mode. 

  The default panic message is “Panic”. 

 

Activating Panic: 

  Press the red and yellow button on the remote control simultaneously. 

  Panic is activated via SMS by sending the E12 the following message: 

$XXXXP, Where XXXX is a four digit numeric pin code. 

  Panic can also be activated by keypad. Press the trouble button, followed 

by 2

nd

 function, followed by the enter button. 

 
Deactivating Panic:
 

  Panic can be deactivated by switching to Off Mode. See section 1.1.3. 

 
1.1.8. Resetting the E12: 
This can only be done when the E12 is in Off Mode. After resetting, the E12’s sensor 
tamper detectors will switch off for 1 hour. All the memory lights, if on, will switch off. 

  Reset by key ring remote: Press all 3 buttons simultaneously. 

  Reset by key pad: Press the Memory button (Mem) followed by enter. 

  Reset by SMS: Send $XXXXr to the E12, where XXXX  is one of the 4 digit, 

numeric user passwords.  

  The E12 will respond with 6 beeps on the internal buzzer. 

  Each time reset is activated the E12 Cleo will send a reset SMS. 

 

1.1.9. Keypad Duress  
A keypad duress signal can be sent if a user is forced to disarm the Alarm. It’s a 
discreet way of letting the Armed Response Company and other users know of the 
situation. 
This Duress signal is sent by entering the user password, but changing the last digit in 
the password to the next higher digit when disarming the alarm. E.g. 1234 would be 
changed to 1235 and 1450 to 1451. 
 

1.2. Access Control and Security 

The E12 can recognize 12 user passwords and 1 master password. Each user 
password is a 4 digit numeric password and the master password is a 6 digit numeric 
password. The same user passwords are used for keypad- as well as SMS commands 
and each user password can be assigned to a name. 
The Master password is used for programming purposes.  
Advanced RF encrypting technology is used for key ring remote control security. 
 

1.3. Other functions

 

1.3.1. Auto Arm / Disarm Time: 

Содержание E12 CLEO





































Отзывы: