Cedar Summit WESTBURY F25030 Скачать руководство пользователя страница 63

Страница: 63 / 68

[email protected]

From inside place 1 (9082) MOD Sunburst Bottom against the (2760) Roof Supports on the Roof Assembly

opening on the Swing Wall. Make sure it sits tight to the Roof Assembly on each side then attach with 2 (S20) #8

x 1-3/8” Wood Screws. (fig. 29.1 and 29.2)

Centre (8305) Starburst Centre lengthway on the outside of (9082) MOD Sunburst Bottom then measure

1-1/4” up from the bottom of (9082) Sunburst Bottom and attach (8305) Starburst Centre with 2 (S20) #8 x 1-3/8”

Wood Screws. (fig. 29.1 and 29.3)

On the inside of the assembly place (9080) MOD Sunburst A tight to the top of (9082) MOD Sunburst Bottom

so the tip is centred at the peak of the Roof Assembly then attach to each (2760) Roof Support and (8305)

Starburst Centre with 3 (S20) #8 x 1-3/8” Wood Screws. (fig. 29.1 and 29.2)

Place 1 (9081) MOD Sunburst B tight to each side of (9080) MOD Sunburst A and tight to the top of (9082)

MOD Sunburst Bottom then attach to each (2760) Roof Support and (8305) Starburst Centre with 2 (S20) #8 x

1-3/8” Wood Screws per board. (fig. 29.1 and 29.2)

Repeat steps A - D to create 2 Sunburst Assemblies

Step 29: Sunburst Assemblies

Swing Wall

Side Wall

Wood Parts

2 x

MOD Sunburst Bottom 1 x 4 x 30”

2 x

Starburst Centre 5/4 x 6 x 12”

4 x

MOD Sunburst B 1 x 4 x 7-1/4”

2 x

MOD Sunburst A 1 x 4 x 11-1/2”

22 x

#8 x 1-3/8” Wood Screw

Hardware

S20

9082

8305

9081

9080

Fig. 29.1

Fig. 29.2

1-1/4”

9082

8305

Fig. 29.3

Outside View

Inside View

9082

9081

9080

S20

x 11

2760

Содержание WESTBURY F25030





































































Результаты поиска

Содержание WESTBURY F25030

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit WESTBURY F25030, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WESTBURY F25030

Отзывы:

Бренды по названию

Популярные бренды