background image

Softener Adjustment

The efficiency of your dishwasher depends on the softness of the tap water. 
To ensure best efficiency, the dishwasher is equipped with a system that 
reduces the hardness in the mains water supply. The efficiency will increase 
when the system is correctly set. To find out the water hardness level of your 
water supply you can use the test strip supplied or alternatively contact your 
local water board.

1.   Open the testing strip (figure 4).
2.   Run water through the tap for one minute.
3.   Hold the testing strip in water for one second.
4.   Remove from the water and shake the test strip to remove excess water.
5.   Wait for one minute.
6.   Check the number of marks on the strip to see the level of water  
 

hardness.

If the hardness of the water you use is above 63 dE or if you are using well 
water; you are recommended to contact your local water board to confirm 
the water hardness level and to use filter and water refinement devices.

Please note: The level of water hardness is preset to level 3.

1.   Press and hold down the programme selection button
2.   Press the Power button to switch on the dishwasher
3.   Keep the programme selection button pressed until “SL” shows on the  
 

display and then disappears

4.   To adjust the level, press the programme selection button until the  
 

required level is shown on the display, as listed in the Table of Water  

 

Hardness below.

5.   To store the selected water hardness level, press the power button.

Water hardness level

British hardness dE

Display shows

1

0-6

L1

2

7-14

L2

3

15-21

L3

4

22-28

L4

5

29-39

L5

6

40-63

L6

Softener adjustment

The efficiency of your dishwasher depends on the softness of the tap water.  To ensure best efficiency, the dishwasher 
is equipped with a system that reduces the hardness in the mains water supply.  The efficiency will increase when the 
system is correctly set.  To find out the water hardness level of  your water supply you can use the test strip supplied or 
alternatively contact your local water board.

1.  Open the testing strip.

2.  Run water through the tap for one minute.

3.  Hold the testing strip in water for one second.

4.  Shake the testing strip after taking it out of the water

5.  Wait for one minute 

6.  Check the number of marks on the strip to see the level of water hardness.

If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use filter and 

water refinement devices.

Please note: The level of water hardness is preset to level 3.

1.  Press and hold down the programme selection button

2.  Press the power button to switch on the dishwasher

3.  Keep the programme selection button pressed until the five programme indicator lights and the end of programme  
 

indicator light flash.

4.  To adjust the level, press the programme selection button until the required level is selected.  The  programme lights  
 

will illuminate as in the table of water hardness settings. 

5.  To store the selected water hardness level, press the power button. 

Testing strip

Adjusting salt consumption

Table of Water Hardness Level Settings

NOTE:

The washing effectiveness of your machine depends on the softness of the tap water. For this

reason, your machine is equipped with a system that reduces the hardness in mains water

supply. The washing effectiveness will increase when the system is correctly set. To find out

the water hardness level of water in your area, contact your local water board or determine

water hardness level by using the test strip(if available).

If the hardness of the water you use is above 90 dF (French hardness) or if you are using well

water; you are recommended to use filter and water refinement devices.

Hardness level is adjusted to level 3 as a factory setting.

9

ENGLISH

Open the

testing

strip.

Run

water

through

your tap

for 1

min.

Keep the

testing

strip in

water for 1

sec.

Shake the

testing strip

after taking it

out of water.

Wait for

1 min.

Make your machine’s water hardness

setting according to the result

obtained through the testing strip.

No Lime
Very low lime content
Low lime content
Medium lime content
Lime content
High Lime content

fig. 4

7

Содержание WC370






















Отзывы: