CDA RC 9301 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

30

The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a
suitably qualified and registered installer. Installers shall take due account of the provi-
sions of the relevant British Standards Code of Practice, the Gas Safety Regulations and
the Building Standards (Scotland)(Consolidation) Regulations issued by the Scottish
Development Department.

Installation to Natural Gas

Installation to Natural Gas must conform to the Code of Practice, etc.
The supply pressure for Natural Gas is 20 mbar.
The installation must conform to the relevant British Standards.

Installation to LP Gas

When operating on Butane gas a supply pressure of 28-30 mbar is required. When
using Propane gas a supply pressure of 37 mbar is required.
The installation must conform to the relevant British Standards.

Warning:

Only a suitably qualified and registered installer, also with technical knowl-

edge of electricity should install the appliance. He should observe the Regulations and
Codes of Practice governing such installation of gas appliances.
Note: It is recommended that the gas connection to the appliance is installed with a
flexible connecting tube made to BS5386.

Notes:

✓

Flexible  hoses  can  be  used  where  the  sited  ambient  temperature  of  the
hose  does  not  exceed  70°C.  These  hoses  must  be  manufactured  in
accordance  with  BS669  part  1  and  be  of  the  correct  construction  for  the
type of gas being used.

✓

Gas hoses designed for natural gas MUST NOT be used for supplying LPG
gas (LPG gas hoses can be identified by a either a red band or stripe on
the rubber outer coating of the hose).
The hose should not be crushed or trapped or be in contact with sharp or
abrasive edges.

Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection
one at a time by brushing the solution over the connection.

The presence of bubbles will indicate a leak.
If there is a leak, tighten the fitting and then recheck for leaks.

IMPORTANT!
Do not use a naked flame to test for leaks.

Gas connection

«
...
28
29
30
31
32
...
»

Содержание RC 9301













































Отзывы:

Нет отзывов

Похожие инструкции для RC 9301

Бренд: Rangemaster Страницы: 48

Бренд: Hamilton Beach Страницы: 44

Бренд: NARVI Oy Страницы: 5

Бренд: M-system Страницы: 120

Бренд: Parkinson Cowan Страницы: 48

Бренд: Gaggenau Страницы: 30

Бренд: K&H Страницы: 9

Бренд: Jenn-Air Страницы: 24

Бренд: IKEA Страницы: 16

Бренд: TriStar Страницы: 48

Бренд: Waldorf Страницы: 25

Бренд: VonShef Страницы: 18

Бренд: Fisher & Paykel Страницы: 27

Бренд: Master Chef Страницы: 3

Бренд: AEG Страницы: 208

Бренд: AEG Страницы: 72

Бренд: Crock-Pot Страницы: 8

Бренд: Crock-Pot Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды