CCX Technologies T-RX Скачать руководство пользователя

Страница: 45 / 60

T-RX™ User Guide

Version 1.4

ADS-B 1090ES / ADS-B 978 UAT Test Item Descriptions

AC 20-165B required elements shown as error if missing or below requirements

Mode S

Address

DF17 ICAO address with registration decoding (USA and Canada only) / Hex /

Octal

Flight ID

DF17 Flight ID. Error if missing

Length /

Width Upper

Bound (Gnd)

Reported when in the ground state. Error if undefined

Latitude /

Longitude

Positive latitude is N, negative is S. Positive longitude is E, negative is W.

1090ES Surface (Gnd) position requires current position set in the config

page to resolve N-S hemisphere and E-W quadrant ambiguity

Note: 1090ES position is decoded using the Global CPR algorithm which fully

utilizes all even/odd data sent in the ADS-B messages

Pressure /

GNSS Altitude

Type is Pressure or GNSS (HAE) as reported by ADS-B transmitter, or "---" if

unavailable. Only reported in Air mode

Geometric

Altitude

Reported if altitude type is pressure and GNSS altitude available. Only

reported in Air mode

Groundspeed

-or-

Airspeed

Heading /

Track

E/W and N/S if GNSS velocity over ground available

Airspeed in knots if groundspeed is not available

Heading/Track Mag/True if groundspeed is not available

Mode A Code Mode A squawk. IDENT, Emerg Alert, Temp Alert if active. Error if missing
Emergency /

Priority Status Emergency/Priority Status type and code
State

Airborne or Surface

Emitter

Category

Category as programmed in the ADS-B transmitter. Error if missing

Содержание T-RX





























































Результаты поиска

Содержание T-RX

Отзывы:

Похожие инструкции для T-RX

Бренды по названию

Популярные бренды

CCX Technologies T-RX, Руководство пользователя

Результаты поиска

Содержание T-RX

Отзывы:

Похожие инструкции для T-RX

Бренды по названию

Популярные бренды