Cayman Systems 2E-H-W Скачать руководство пользователя страница 135

Страница: 135 / 170

Cayman 2E-H-W User’s Guide

Diagnostic Console

November 2000

B-7

revert

The

revert

command retrieves the saved version of settings from

non-volatile storage and overwrites any changes made since the last
save.

save

The

save

command saves the EPROM settings you have entered or

changed to non-volatile storage in the Cayman 2E-H-W.

show

The

show

command displays the current EPROM settings for the

Cayman 2E-H-W and a brief explanation of those settings. For
example, the show command produces the following:

BootPROM> show

flash on

(flash will be tried)

ip 0

(no ip address; tftp will not be tried)

file <unset>

(must be set for tftp download)

bootp on

(will attempt configuration via bootp)

autoboot 10

(will autoboot on powerup, and will try

10 times)

autoprog never

(will never program a downloaded

image into flash)

Cayman 2E-H-W serial no. 800700, h/w rev. 1, eprom v1.3

Last install status: code flash successfully programmed

flash image 1: Cayman 2E-H-W 5.3.0

Boot Setting
Commands

The following commands specify boot settings for the Cayman
2E-H-W.

autoboot { retry_count | off }

The

autoboot

retry_count

command (where

retry_count

is any

whole number) sets the number of times the Cayman 2E-H-W should
attempt to start an image and run it when powered up. If you enable
autoboot with the

autoboot retry_count

command, the autoboot

Содержание 2E-H-W











































































































































































Результаты поиска

Содержание 2E-H-W

Отзывы:

Похожие инструкции для 2E-H-W

Бренды по названию

Популярные бренды

Cayman Systems 2E-H-W, Руководство пользователя

Результаты поиска

Содержание 2E-H-W

Отзывы:

Похожие инструкции для 2E-H-W

Бренды по названию

Популярные бренды