CAT Pumps 3570 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

CAT Pumps 3570 Series Скачать руководство пользователя страница 15

SERVICE MANUAL | 3570 Series Plunger Pumps

15

(763) 780-5440 | [email protected] | www.catpumps.com

Servicing the Seals

MANIFOLD AND SEAL INSTALLATION

1.62 Install backup rings, then O-rings into the

large grooves on the end of the V-packing
cylinders.

1.63 Install the O-rings into the smaller grooves on

the other end of the V-packing spacers.

1.64 Install the coil springs into the V-packing

cylinders.

1.67 Install the second V-packings with the

grooved sides also facing down.

1.68 Install the female adapters with grooved sides

facing down into the V-packing cylinders.

1.69 Install V-packing spacer with the smaller

diameter sides facing down and press them
into place.

1.65 Install the male adapters into the V-packing

cylinders with the flat sides facing down.

NOTICE: There are two O-rings for each

V-packing cylinder. The thicker O-ring goes in

the larger groove with the backup ring.

1.66 One side of the V-packing has a groove. Install

the first V-packings with the grooved sides
facing down and press them into place.

«
...
13
14
15
16
17
...
»

Содержание 3570 Series





























Отзывы:

Нет отзывов