background image

E-16

To initialize the Label Printer

1. Turn power off.
2. While holding down the 

PRINT

 and 

ESC

 keys,

press 

ON

 to turn power on.

3. Keeping 

PRINT

 and 

ESC

 held down, release

the 

ON

 key only.

This prompt confirms whether or not you want to
initialize the Label Printer.

4. Press 

SET

 to initialize the Label Printer or 

ESC

 to abort the reset operation.

The following table shows the initial settings.

Troubleshooting

INT?

Action

Use only one 

¥

 mark.

Only two lines of text
can be input, so text
can contain only one

¥

 mark.

Do not use 

¥

 marks.

6mm tape can have
only one line of text,
so text cannot contain
any 

¥

 marks.

Delete the 

¥

 mark to

print on 6mm tape or
switch back to a wider
tape.

Shorten the text to be
printed and try again.

Change the tape width
setting to OFF and try
printing the stamp
again.

Delete text from one of
the text memory areas
and then store the new
text.

Replace batteries.

Initialize the Label
Printer.

Problem

ERR! message
on the display.

FUL! message
on the display.

BATT message
on the display.

ERR! message
on the display.

Possible Cause

Attempt to input two 

¥

marks within the same
text.

Attempt to input 

¥

mark while 6mm is
specified as the tape
width.

Label text containing a

¥

 mark was input and

then tape width
specification was
changed to 6mm.
(ERR! message appears
when you try to perform
a print operation.)

Text that is longer than
5.5cm when stamp
printing is selected.

Attempt to print a stamp
while 6mm is specified
for the tape width.

Both text memory areas
(AREA 1 and AREA 2)
already contain text.

Battery power is too
low.

Memory data has
become corrupted for
some reason.

Item

Display

Memory

SYMBOL

EFFECT
M-FEED

MIRROR

MEMO

DENSITY

WIDTH

Reset

Cleared

Cleared

,

CANCEL

NO

OFF

STR?

3

OFF

Содержание KL 750B - 2 Line Label Printer




















Отзывы: