Case 1021G Скачать руководство пользователя страница 47

Страница: 47 / 61

Engine - Engine and crankcase

30. Loosen the hexagonal nut of the outlet temperature

sensor

(1)

Loosen the hexagonal nut of outlet the Nitrogen Ox-
ides (NOx) sensor

(2)

Loosen the hexagonal nut of the ammonia (NH3) sen-
sor

(3)

Remove any straps holding the sensor wiring harness
to the others. Disconnect the temperature sensor

(1)

NOx, sensor

(2)

and the NH3

(3)

sensor from the out-

let

(4)

of the Selective Catalytic Reduction (SCR)

(5)

LEIL15WHL0672AB

31. Locate the inlet temperature sensor

(1)

and the inlet

NOx sensor

(2)

on the inlet of the Diesel Oxidation

Catalyst (DOC)

(3)

Loosen the hexagonal nut of the inlet temperature
sensor

(1)

and the inlet NOx sensor

(2)

Disconnect the sensors

(1)

and

(2)

from the inlet of

the Diesel Oxidation Catalyst (DOC)

(3)

LEIL15WHL0671AB

32. Loosen the hexagonal nut

(1)

, with related washer,

spacer, and bolt. Separate the P-clamp

(2)

that secure

the wiring harness

(4)

of the DOC inlet temperature

sensor from the support bracket

(3)

LEIL15WHL1141AB

33. Remove the two bolts

(3)

and the related washers and

nuts to separate the exhaust support bracket

(5)

from

the U-clamp

(4)

34. Remove the clamp

(1)

from the inlet Diesel Oxidation

Catalyst (DOC) pipe

(2)

Discard the gasket.

LEIL15WHL0826AB

51428268_EN 19/12/2017

10.1 [10.001] / 12

Содержание 1021G






























































Результаты поиска

Содержание 1021G

Отзывы:

Похожие инструкции для 1021G

Бренды по названию

Популярные бренды

Case 1021G, Руководство по обслуживанию

Результаты поиска

Содержание 1021G

Отзывы:

Похожие инструкции для 1021G

Бренды по названию

Популярные бренды