manualshive.com logo in svg

Case 1021G, Руководство по обслуживанию

Поделиться
Скачать
Case 1021G Скачать руководство пользователя страница 19

INTRODUCTION

Waste disposal

Improperly disposing of waste can threaten the environ-
ment.

Each country has its own Regulations on this subject. It
is therefore advisable to prepare suitable containers to
collect and store momentarily all solid and fluid materials
that must not be scattered in the environment to avoid
pollution.

These products will be delivered at preset intervals follow-
ing the forward environmental regulation.

Below are listed some products from the machine requir-
ing disposal:

• Lubricating oil

• Brake system oil

• Coolant mixture, condensation rests and pure an-

tifreeze

• Fuel

• Filter elements, oil and fuel filters

• Filter elements, air filters

• Battery

Also polluted rags, paper, sawdust and gloves must be
disposed in compliance with the same procedures.

Do not use food or beverage containers that may mislead
someone into drinking from them. Do not pour waste onto
the ground, down a drain, or into any water source. Air
conditioning refrigerants escaping into the air can damage
the Earth’s atmosphere. Government regulations may re-
quire a certified air conditioning service centre to recover
and recycle used air conditioning refrigerants. Obtain in-
formation on the proper way to recycle or dispose of waste
from your local environmental or recycling centre, or from
your Dealer.

TULI12WEX2022AA

19

51428268_EN 19/12/2017

12

Содержание 1021G






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды