Case IH FARMALL 40C Скачать руководство пользователя | Manualshive

Страница: 38 / 51

background image

INTRODUCTION

Protecting the electronic and/or electrical systems during charging and welding

To avoid damage to the electronic and/or electrical systems, always observe the following practices:

1. Never make or break any of the charging circuit connections when the engine is running, including the battery

connections.

2. Never short any of the charging components to ground.

3. Always disconnect the ground cable from the battery before arc welding on the machine or on any machine

attachment.

• Position the welder ground clamp as close to the welding area as possible.

• If you weld in close proximity to a computer module, then you should remove the module from the machine.

• Never allow welding cables to lie on, near, or across any electrical wiring or electronic component while you

weld.

4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery

charger.

NOTICE:

If you must weld on the unit, you must disconnect the battery ground cable from the machine battery.

The electronic monitoring system and charging system will be damaged if this is not done.

5. Remove the battery ground cable. Reconnect the cable when you complete welding.

WARNING

Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0111A

Special tools

The special tools that CASE IH suggests and illustrate in this manual have been specifically researched and designed
for use with CASE IH machines. The special tools are essential for reliable repair operations. The special tools are
accurately built and rigorously tested to offer efficient and long-lasting operation.

By using these tools, repair personnel will benefit from:

• Operating in optimal technical conditions

• Obtaining the best results

• Saving time and effort

• Working in safe conditions

47941906 16/03/2016

31

«
...
36
37
38
39
40
...
»

Содержание FARMALL 40C




















































Отзывы:

Нет отзывов

Похожие инструкции для FARMALL 40C

Бренд: Komatsu Страницы: 195

Бренд: Agriweld Страницы: 17

FORTERRA HD Series

Бренд: Zetor Страницы: 168

POWERGRIP PG Series

Бренд: Parker Страницы: 34

Бренд: Baroness Страницы: 76

Бренд: Kellfri Страницы: 16

Бренд: GE Страницы: 24

Profile GCG1580L

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды