Casablanca Reverie Скачать руководство пользователя страница 15

15

R

EVERIE

Fan Finishes
•  For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the fi nish.
•  A vacuum cleaner brush nozzle can remove heavier dust.
•  Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened 

soft cloth. An antistatic agent may be used, but 

never use abrasive cleaning agents

 as these will damage the fi nish.

Blades
• Wood-fi nish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be 

applied for added protection and beauty.

•  For painted and high-gloss blades,  surface smudges or an accumulation of dirt and dust can be removed easily using a mild 

detergent and slightly dampened soft cloth. An antistatic agent may be used, but 

never use abrasive cleaning agents

 as these 

will damage the fi nish.

No Need for Lubrication
• 

Never lubricate this fan! 

 Th

  e precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated 

for life. 

•  Do not attempt to oil the motor.

Changing Lightbulbs
•  Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
•  Replace bulbs with the same type as you removed from the light fi xture. 
• Th

  e maximum wattage rating for this fan’s light kit is 100 watts for the uplight, 120 watts for the downlight.

CARE RECOMMENDATIONS

Th

  is device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. Th

  is device may not cause harmful interference.

2. Th

  is device must accept any interference received, including interference that may cause undesired operation. 

Th

  is equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the 

FCC rules. Th

  ese limits are designed to provide reasonable protection against harmful interference in a residential installation. 

Th

  is equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference 
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off  and on, the user is encouraged to try to correct the interference by 
one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

NOTE:  Any changes or modifi cations to the transmitter or receiver not expressly approved by Casablanca Fan Company 
may void one's authority to operate this remote control.

For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178 

or visit us on the web at:  www.casablancafanco.com

Содержание Reverie



















Отзывы: