background image

6

MoUntInG recoMMendatIonS

Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and 

fan size are all important factors to consider before installation.

Location

Ceiling fans have practical uses in almost every room in your home. We suggest 

you follow these mounting recommendations as you decide where to install 

your Casablanca fan. 
•  For  safety  reasons,  the  fan  blades  must  be  a  minimum  of  7'  above  the 

floor. 

•  Do not locate the fan in a doorway or above a swinging door. 
•  In bedrooms, fans work best when mounted above the foot of the bed.
•  Over pool tables, be sure to provide plenty of clearance to avoid damage 

from pool cues.

•  In  kitchens,  be  sure  to  allow  for  open  cupboard  doors  to  clear  the  fan 

blades.

•  Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and 

warp the blades.

Fan Size

Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may 

be needed.

General GUIdelIneS

Calculation of Ceiling angle

Use the tear-off 

Ceiling Angle Template

 card inserted 

in this manual. It provides you with a simple “go” or 

“no-go” for installing your fan on a sloped ceiling.

7' minimum

When to use extension Poles

For  optimum  performance  and  appearance,  an 

extension pole should be used with your Casablanca 

fan  when  installing  on  high  (cathedral)  ceilings  or 

sloped ceilings. Casablanca offers standard poles in 

increments of 6" up to 5'. Custom poles are available 

in lengths up to 9'9". See your Authorized Casablanca 

Dealer for details.

Blades must be a 

minimum of 7 feet 

above the floor

Extension 

Pole

Maximum 

hang-tru

®

 

angle 32º

This slope is less than 32º.

It is OK to install your fan

.

T

his slope is 32º. This is the maxi-

mum slope that will allow the fan to 

hang straight down.  It is OK to install 

your fan.

This slope is more than 32º. Your 

fan will not hang straight down; an 

adapter is necessary. Contact your 

local Authorized Casablanca Dealer 

in regards to purchasing a “Sloped 

Ceiling Adapter.”

note:

 Fan may wobble or vibrate if pole length is 

not  long  enough  and  inside  blade  is  too  close  to 

downslope  or  side  wall.  Extending  pole  length  will 

usually solve the problem.

Sloped ceIlInG InStallatIonS

SuGGeSted extenSion PoLe LenGthS

 

Ceiling Height 

Pole Length

 

8' 0" 

3.5"

 

8' 6" 

3.5"

 

9' 0" 

12"

 

9' 6" 

12"

 

10' 0" 

18"

 

11' 0" 

24"

 

12' 0" 

36"

 

13' 0" 

48"

 

14' 0" 

60"

exaMPLe 3

exaMPLe 2

exaMPLe 1

Содержание C31uxxB



























Отзывы: