background image

12

BLADE INSTALLATION

Blade Irons (5)

Blade Iron 

Screws (11)

BLADE HARDWARE (not to scale)

Blades (5) 

(packed separately)

Blade Badges (5)

Blade Screws (21)

Step 8.

 Remove the five shipping blocks, washers, 

and screws as shown in Figure #1. DO NOT discard 

the five screws; you will need them for installing the 

blades onto the fan.

SHIPPING BLOCK

Attach Blade Irons
Step 9.

 Attach a blade to a blade iron by first pressing 

the blade badge onto the blade, then attaching the 

blade iron using four blade screws as shown in Figure 

#1. Using the provided screwdriver, tighten securely 

by hand only. 

Repeat for each blade assembly.

Blade Installation
Step  10.

  Before  attempting  to  attach  the  blades, 

review Figure #3 for blade placement on the blade 

holder  adapter  ring. The  numbers  and  lines  show 

screw placement when attaching the five blade irons 

and  blades  assemblies  to  the  fan.  When  placing 

the blades on the adapter ring, each blade iron will 

cover one of the five adapter ring mounting screws 

as shown.

Figure #1

BLADE IRON

BLADE BADGE

BLADE

BLADE BADGE 

SCREWS

Figure #3

Figure #2

Phillips  

Screwdriver

BLADE 

HOLDER 

ADAPTER 

RING

NOTE:

  Blades  are  packaged  separately  based  on 

blade style. For illustrative purposes, the BL-ADK-RA 

(Adirondack Reclaimed Antique) blades are shown. 

Please use the instructions below for all three blade 

types.

Содержание C19xxxK





















Отзывы: