background image

16

Fan Finishes

• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened

soft cloth. An antistatic agent may be used, but 

never use abrasive cleaning agents

 as these will damage the finish.

Blades

• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be

applied for added protection and beauty.

• For painted and high-gloss blades,  surface smudges or an accumulation of dirt and dust can be removed easily using a mild

detergent and slightly dampened soft cloth. An antistatic agent may be used, but 

never use abrasive cleaning agents

 as these

will damage the finish.

No Need for Lubrication

Never lubricate this fan! 

 The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated

for life.

• Do not attempt to oil the motor.

Changing Lightbulbs

• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light fixture.
• The maximum wattage rating for this fan’s light kit is 360 watts for the downlight.

CARE RECOMMENDATIONS

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE:  Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company
may void one's authority to operate this remote control.

For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178

or visit us on the web at:  www.casablancafanco.com

Содержание BAROLO





















Отзывы: