Casablanca 19 Century Скачать руководство пользователя страница 14

The Light-Minder program automatically turns OFF the fan mounted lights after 

two hours.

To enter the Light-minder Program:

1. Turn the 

 

OFF for at least three seconds.

2. Turn the 

 

ON.

3. Immediately operate the buttons in the following sequence:

 

+

 

 

+

 

 

+

 

4. A series of tones indicates this command has been accepted.

The fan and light will operate normally using the buttons to turn them on and off. 

But, if the lights are left on, they will automatically shut off after two hours. To 

cancel the Light-Minder Program, turn the 

 

off for three seconds.

INTELI•TOUCH OPERATION 

f

 SAFE-EXIT

®

 PROGRAM

The Safe-Exit Program gives you about thirty seconds of light when you turn 

the lights off, enabling you to exit your home before the lights go out.

To enter the Safe-Exit Program:

1. Turn the 

 

off for at least three seconds.

2. Turn the 

 

on.

3. Immediately operate the buttons in the following sequence:

 

+

 

 

+

 

 

+

 

after

 you hear the confirming audio

tones from the fan - 

immediately press

4. The lights will blink to indicate this command has been accepted.

The lights will stay on for twenty seconds and then begin to dim. After a total 

of thirty seconds has elapsed, the lights will be off completely. To cancel the 

Safe-Exit Program, turn the 

 

off for three seconds.

INTELI•TOUCH OPERATION 

f

 

HOME-SAFE

®

 PROGRAM

The Home-Safe Program makes an unoccupied home appear occupied by turning 

the lights on and off at random times.

To enter the Home-Safe Program:

1. Turn the 

 

off for at least three seconds.

2. Turn the 

 

on.

3. Immediately operate the buttons in the following sequence:

 

+

 

 

+

 

 

+

 

4. A tone and flashing light indicate this command has been accepted.

This program overrides all manual control of lights and fan. The lights will now be 

automatically cycled on and off in a controlled sequence as follows: On 1 hour, off 

1

/

2

 hour, on 2 hours, off 1 hour, on 

1

/

2

 hour then off 2 hours.

This seven hour pattern will repeat continuously so that a different pattern of 

lighting is seen each day of the week.     

To cancel the Home-Safe Program, turn the 

 

off for three seconds.

INTELI•TOUCH OPERATION

 

f

 FAN-MINDER

 PROGRAM

The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the 

speed of the fan each two-hour interval to compensate for the cooling night air. 

To enter the Fan-minder Program:

1. Turn the 

 

off for at least three seconds.

2. Turn the 

 

on.

3. Immediately operate the buttons in the following sequence:

 

+

 

 

+

 

 

+

 

4. The fan controller will respond with three descending tones. A timer is now initiated and the fan 

will reduce one speed for each two-hour interval. The fan will not, however, descend below the 

second lowest speed.

To cancel the Fan-Minder Program, turn the 

 

off for three seconds. You may increase the fan 

speed by pressing and holding the 

 button until the desired speed is reached, then release 

it. The fan will again reduce one speed for each 2 hour interval.

INTELI•TOUCH OPERATION 

f

 LIGHT-MINDER

®

 PROGRAM

note:

 Both Light-Minder and Safe-Exit 

programs  can  run  at  the  same  time, 

however the dimmer cannot be used, 

the light may only be turned ON/OFF.

POWER

FAN

POWER

FAN

LIGHT

LIGHT

POWER

POWER

POWER

FAN

FAN

LIGHT

LIGHT

LIGHT

POWER

POWER

POWER

FAN

LIGHT

FAN

LIGHT

POWER

POWER

POWER

FAN

LIGHT

FAN

LIGHT

FAN

POWER

Inteli•Touch

®

Содержание 19 Century




















Отзывы: