Casablanca 19 Century Скачать руководство пользователя страница 11

Страница: 11 / 19

gLASS SHADE

SCREWS

Step 18.

Slide the light kit over the

threaded pipe from the switch housing.

Assure that no wires are pinched.

Secure the light kit to the fan with the

finial.

Tighten securely

by hand

only.

FINIAL

THREADED

PIPE

Step 19.

Loosen the three glass screws for each

fixture so the end of the screws are flush with

the inside of the fixture.

Slide the glass shade into the fixture and hold

firmly. Turn each screw several times, going

in a circle, to assure that all glass screws have

engaged the glass.

Tighten securely by

hand

only.

Step 20.

Install the four 60-watt G-16.5 bulbs

into each fixture.

gLASS SHADE

60 WATT TyPE g-16.5

CANDELABRA-BASE BULB

gLASS SHADE

GLASS & BULB INSTALLATION

GLASS HARDWARE

INSTALL LIGHT KIT

Century

™

60 WATT TyPE g-16.5

CANDELABRA-BASE BULB

Содержание 19 Century




















Результаты поиска

Содержание 19 Century

Отзывы:

Похожие инструкции для 19 Century

Бренды по названию

Популярные бренды

Casablanca 19 Century, Руководство пользователя

Результаты поиска

Содержание 19 Century

Отзывы:

Похожие инструкции для 19 Century

Бренды по названию

Популярные бренды