background image

CIRCUIT BREAKER

(Trip breaker for The

circuiT you will be

working on)

FUSE BOX

(remove fuse for The

circuiT you will be

working on)

  The  blades  in  each  pack  are  matched  for 

equal weight to assure smooth fan operation. 

If more than one fan is being installed, be 

careful  not  to  mix  blades  from  different 

cartons.

  Inspect  the  contents  of  your  carton  for 

possible shipping or handling damage and 

report  any  such  damage  directly  to  your 

authorized Casablanca dealer.

  It is always a good idea to have an assistant 

to help with the installation.

  When  cleaning,  painting,  or  working  near 

your  fan,  be  very  careful  of  the  fan  and 

blades.  Always  turn  the  power  OFF  to  the 

ceiling fan before servicing it, working on 

it, or replacing light bulbs. 

  Never insert anything into the path of the 

fan blades while the fan is in operation.

•  Never install a fan over a pool or spa. 

  Never operate a fan that has been damaged in 

any way. Contact Casablanca Fan Company by 

calling 1-888-227-2178, or contact your local 

authorized Casablanca dealer for assistance 

in obtaining service.

CONTENTS

READ AND SAVE THESE INSTRUCTIONS

• 

All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical 

codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-

cian should be consulted if you are unsure.

•  This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan 

installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling 

installations.

• 

This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum 

current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light 

current is 2.8 amps or 340 watts of lighting.

  Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make 

sure all wires are within the canopy and that no wires are being pinched.

For best performance and for your warranty to be valid,

use only genuine Casablanca blades, light fixtures, and accessories.

Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product 

and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this 

owner’s manual completely and carefully. Retain this manual for future reference.

SAFETY FIRST

P/N6943020  AT0507

cauTion: To avoid possible electrical shock, make certain that electricity is turned off at 

the circuit breaker or fuse box before attempting any installation procedure.

18

84

70

SAFE USE

BEFORE YOU START

INTRODUCTION 

1

mOUNTINg ReCOmmeNDaTIONs 

2

faN INsTaLLaTION 

3

OpTIONaL  LIghT fIxTURe INsTaLLaTION 

10

CONTROL feaTURes:
 

INTeLI•TOUCh OpeRaTION 

12

 

TROUbLeshOOTINg 

15

 

aDVaN•TOUCh OpeRaTION 

16

 

TROUbLeshOOTINg 

19

Содержание 19 Century




















Отзывы: