background image

NORMAL OPERATION (Dayparts Enabled) 

CAUTION: 
HOT SURFACE 

 
 

Inner surfaces of the unit 
will be very hot during and 
after operation.  Avoid 
touching the cabinet when 
loading or removing      
product. 

Daily operating procedures 

 
1.  Prior to use, unit must be installed properly and tested by a trained instal-

lation or service professional. 

2.    Unit must be clean and grease-free prior to use. 
3.    Verify that the removable interior caddy is installed properly. 
4.  Turn power on by flipping the toggle switch; the motors should begin to 

turn and create airflow. 

5.  Unit will automatically begin to preheat, allow 20 minutes for unit to climb 

to operating temperature of 180º F.  Digital readout will display “LO” until 
the cabinet reaches 122º F. After the cabinet reaches 122º F, the digital 
readout will display the current temperature, until the cabinet reaches the 
setpoint. 

6.  Once the cabinet reaches the setpoint, the digital readout will display 

“P1”.  This indicates the cabinet is at temperature and ready to hold 
product. 

7.  Load product into pans and insert pans into the Crisp ‘N Hold. 
8.  The cabinet has six programmable timers (“P1”, “P2”, “P3”, “P4”, P5”, 

P6”) for each pan (if holding maximum capacity of six 1/3 size pans). 
Different program times can be used for different parts of the day (i.e. 
Breakfast, Lunch, Dinner) or for alternate products. 

9.  Press the INCREASE KEY

*

             or DECREASE KEY

*

              to  

 
 
        select the desired program timer (display will scroll through P1 through 
        P6). 
10.  Once a timer menu (P1-P6) has been selected, press TIME KEY 
 
 
        to start the program. Refer to 

Controller Programming

 on pages 7 and 8  

        to change programmed time. The digital readout will count down, 
        displaying the remaining time. When the timer reaches 5 minutes  
        remaining, the timer will display “5” and will beep for 5 seconds. The  
        digital readout will display in hours and minutes until it reaches less than 
        one minute. When time remaining is less than a minute, the digital  
        read out will count down in seconds.  At the end of the timed cycle, the 
        digital readout will flash “000” and an alarm will sound until the TIME 
        KEY is pressed. The digital readout will display the currently selected 
        timer (i.e. “P1”), indicating that the cabinet is ready to hold product. 
11.   Remove the product pan from the cabinet. 
12.  If holding is finished and cabinet is not needed for an extended time,  
       turn the TOGGLE SWITCH to “OFF” and perform cleaning procedure as  
       described on page 8. 

NOTE: 

Timer can be 

cancelled at any time 
during the cycle by 
pressing and holding the 
TIME KEY for 2 seconds. 
Digital readout will display 
currently selected timer 
(e.g “P 1”). 

NOTE: 

Press and release 

the TEMP KEY top view or 
verify a cavity setpoint.  

Tempera-
ture 

Typical 

Tempera-
ture 

Module is 
READY

 

Typical 

Time 

Remaining

 

Timed Cycle 

Completed

 

NOTE: 

Program timer 

defaults to “P1” each time 
the unit is turned 

OFF 

then back 

ON

NOTE: 

Timer can not be 

started until the cabinet is 
pre-heated.

 

NOTE: 

See 

PROGRAMMING INSTRUCTIONS 

on next page with 

instructions on how to enable DAYPARTS 

Timer Keys 

Temperature 

Key 

Digital Readout  

(one for each key) 

On/Off  

Toggle Switch 

*

Increase/Decrease Keys 

top for timers 1,2,3; bottom for timers 4,5,6 

Содержание VCNH3W2S













Отзывы: