background image

 

TB0354A 

Page 6 of 8 

09/27/05 

MAN/PHSR             HORN 

VOLUME 

 

 

RAD        PA 

 

YELP 

 

WAIL 

 

STBY 

 

RADIO 

OPERATION 

 

 Sound 

Hazard 

- Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.  

Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. 

 

(Ref. OSHA 1910.95 for occupational noise exposure guidelines) 

 

 
The 

OFF/ON

 Rocker Power Switch controls the siren power.  The siren may be left on any time the vehicle is in 

operation.  The power should be turned off when vehicle is not being used to conserve battery power. 
 
The Rotary Function Switch selects various operating modes.  These modes are as follows: 
 

Yelp, Wail, and Standby: 

A silent mode that allows Horn and Public Address 
operation. 

 

Radio: 

This mode reproduces, or repeats, the output of a radio.  The radio must 
be connected and RADIO VOLUME on the face adjusted.  No Horn or PA 
operation are available in this position. 

 

Manual /  
Phaser: 

Disabled 

 

Horn: 

This push-button switch provides a simulated air-horn tone while pressed.  
This can be used to supplement the normal vehicle horn and is useful at 
intersections or in low noise areas.  This tone is available with selector 
switch in Yelp, Wail, or Standby. 

 

PA: 

Pressing the microphone button in any mode except Radio changes the unit to PA (Public Address).  The 
mode resumes when the button is released.  Adjust the PA Volume and hold the microphone close to your 
lips for proper operation. 

 
 

Volume Controls 

Volume controls are provided for radio repeat function volume and public address volume.  
These should be set when the vehicle is parked.  Set the RAD volume with the selector switch 
in the Radio position and the radio volume set to desired level.  Set the PA volume to the 
maximum level with no feedback (squeal). 
 
 

Auxiliary Input 

During installation an auxiliary input may be connected to the horn ring or other switching device.  It provides the same 
operation as pressing the Horn button. 
 

Cutout 

During installation a cutout input may be connected to a door switch.  It turns off Horn when the door is opened.  The 
Horn tone will continue to be cut off even while the door is opened. 
 

Содержание SA-500-11 14V









Отзывы: