Carrier WeatherMaster 48HC Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 56

background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480254-01

Printed in U.S.A.

Form 48HC-4-6-03SI

Pg 1

1-2020

Replaces: 48HC-4-6-02SI

Installation Instructions

CONTENTS

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1
MODEL NUMBER NOMENCLATURE AND

DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rated Indoor Airflow  . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Jobsite Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 1 — Plan for Unit Location   . . . . . . . . . . . . . . . 10

Step 2 — Plan for Sequence of Unit Installation . . 10

• CURB-MOUNTED INSTALLATION

• PAD-MOUNTED INSTALLATION

• FRAME-MOUNTED INSTALLATION

Step 3 — Inspect Unit . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 4 — Provide Unit Support . . . . . . . . . . . . . . . . 10

• ROOF CURB MOUNT

• SLAB MOUNT (HORIZONTAL UNITS ONLY)

• ALTERNATE UNIT SUPPORT (IN LIEU OF CURB OR

Step 5 — Field Fabricate Ductwork . . . . . . . . . . . . . 12
Step 6 — Rig and Place Unit . . . . . . . . . . . . . . . . . . 12

• POSITIONING ON CURB

Step 7 — Convert to Horizontal and Connect

Ductwork (When Required) . . . . . . . . . . . . . . . . . 13

Step 8 — Install Outside Air Hood . . . . . . . . . . . . . . 14

• ECONOMIZER AND TWO POSITION DAMPER HOOD

PACKAGE REMOVAL AND SETUP (FACTORY

• ECONOMIZER AND TWO-POSITION HOOD

Step 9 — Units with Hinged Panels Only   . . . . . . . . 15
Step 10 — Install Flue Hood  . . . . . . . . . . . . . . . . . . . 15
Step 11 — Install Gas Piping  . . . . . . . . . . . . . . . . . . 16

• FACTORY OPTION THRU-BASE CONNECTIONS

(GAS CONNECTIONS)

Step 12 — Install External Condensate Trap and

Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 13 — Make Electrical Connections . . . . . . . . . 19

• FIELD POWER SUPPLY

• UNITS WITH FACTORY-INSTALLED NON-FUSED

DISCONNECT OR HACR

• UNITS WITHOUT FACTORY-INSTALLED NON-

FUSED DISCONNECT OR HACR

• CONVENIENCE OUTLETS

• HACR AMP RATING

• FACTORY-OPTION THRU-BASE CONNECTIONS

(ELECTRICAL CONNECTIONS)

• UNITS WITHOUT THRU-BASE CONNECTIONS

(ELECTRICAL CONNECTIONS)

• FIELD CONTROL WIRING

• HEAT ANTICIPATOR SETTINGS

• HUMIDI-MIZER® CONTROL CONNECTIONS

• LOW AMBIENT CONTROL (FACTORY OPTION)

• INTEGRATED GAS CONTROLLER

• COMFORTLINK (FACTORY OPTION)

• TYPICAL WIRING DIAGRAMS

Economi$er® X (Factory Option) . . . . . . . . . . . . . . .41

• SYSTEM COMPONENTS

• SPECIFICATIONS

• ENVIRONMENTAL

• ECONOMIZER MODULE WIRING DETAILS

• INTERFACE OVERVIEW

• SETUP AND CONFIGURATION

• ENTHALPY SETTINGS

• TROUBLESHOOTING

PremierLink™ (Factory Option)  . . . . . . . . . . . . . . . .51
RTU Open Controller (Factory-Installed Option)   . .51
Smoke Detectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

• COMPLETING RETURN AIR SMOKE SENSOR

• ADDITIONAL APPLICATION DATA

Step 14 — Adjust Factory-Installed Options . . . . . .53

• SMOKE DETECTORS

• ECONOMI$ER IV OCCUPANCY SWITCH

Step 15 — Install Accessories . . . . . . . . . . . . . . . . .53
Step 16 — Check Belt Tension . . . . . . . . . . . . . . . . .53

• BELT FORCE — DEFLECTION METHOD

• BELT TENSION METHOD

Pre-Start and Start-Up . . . . . . . . . . . . . . . . . . . . . . . .54
START-UP CHECKLIST . . . . . . . . . . . . . . . . . . . . .CL-1

SAFETY CONSIDERATIONS

Installation and servicing of air-conditioning equipment can be

hazardous due to system pressure and electrical components. Only

trained and qualified service personnel should install, repair, or

service air-conditioning equipment.
Untrained personnel can perform basic maintenance functions of

cleaning coils and filters and replacing filters. All other operations

should be performed by trained service personnel. When working

on air-conditioning equipment, observe precautions in the litera-

ture, tags and labels attached to the unit, and other safety precau-

tions that may apply.
Follow all safety codes, including ANSI (American National Stan-

dards Institute) Z223.1. Wear safety glasses and work gloves. Use

quenching cloth for unbrazing operations. Have fire extinguisher

available for all brazing operations.
It is important to recognize safety information. This is the safety-

alert symbol

. When you see this symbol on the unit and in in-

structions or manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, CAUTION,

and NOTE. These words are used with the safety-alert symbol.

DANGER identifies the most serious hazards which

will

result in

severe personal injury or death. WARNING signifies hazards

which

could

result in personal injury or death. CAUTION is used

to identify unsafe practices, which

may

result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which

will

result in enhanced installation, reliability,

or operation.

WeatherMaster

®

48HC**04-06 Single Package Rooftop

Gas Heating/Electric Cooling Unit

with Puron

®

(R-410A) Refrigerant

Downloaded from

1
2
3
...
»

Содержание WeatherMaster 48HC Series

























































Отзывы:

Нет отзывов

Похожие инструкции для WeatherMaster 48HC Series

Бренд: Daitsu Страницы: 21

Бренд: Daitsu Страницы: 21

Бренд: Daitsu Страницы: 21

Бренд: Daitsu Страницы: 21

Бренд: INVENTOR Страницы: 136

Бренд: Orbegozo Страницы: 143

Бренд: Hyundai Страницы: 52

Бренд: EarthLinked Страницы: 16

Бренд: Bard Страницы: 23

Бренд: Kelvinator Страницы: 16

Pioneer Eclipse 250AP115

Бренд: Amano Страницы: 64

NTC5/GNJ Series

Бренд: ICP Страницы: 16

Бренд: Floater Страницы: 12

Бренд: acerpure Страницы: 40

Mr.Slim MSZ-A09NA

Бренд: Mitsubishi Страницы: 15

Бренд: Snap-On Страницы: 52

GWH09MA-K3DNA3L

Бренд: Gree Страницы: 89

WMMS-09EW-V2B(59)4

Бренд: YMGI Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды