manualshive.com logo in svg

Carrier WeatherMaster 48HC Series, Руководство по установке

Поделиться
Скачать
Carrier WeatherMaster 48HC Series Скачать руководство пользователя страница 25

25

Fig. 45 — Edge Pro Thermidistat

Connecting the Carrier Humidistat (HL38MG029)

1. Route the humidistat 2-conductor cable (field-supplied)

through the hole provided in the unit corner post.

2. Feed wires through the raceway built into the corner post (see

Fig. 43) to the 24-v barrier located on the left side of the con-
trol box. The raceway provides the UL-required clearance

between high-voltage and low-voltage wiring.

3. Use wire nuts to connect humidistat cable to two PINK leads

in the low-voltage wiring as shown in Fig. 46.

Connecting the Thermidistat device (33CS2PPRH-01)

1. Route the Thermidistat multi-conductor thermostat cable

(field-supplied) through the hole provided in the unit corner

post.

2. Feed wires through the raceway built into the corner post (see

Fig. 43) to the 24-v barrier located on the left side of the con-

trol box. The raceway provides the UL-required clearance
between high-voltage and low-voltage wiring.

3. The Thermidistat has dry contacts at terminals D1 and D2 for

dehumidification operation (see Fig. 47). The dry contacts
must be wired between CTB terminal R and the PINK lead to

the LTLO switch with field-supplied wire nuts. Refer to the

installation instructions included with the Carrier Edge Pro
Thermidistat device for more information.

Fig. 46 — Typical Humidi-MiZer Adaptive Dehumidification System Humidistat Wiring

®

Downloaded from 

ManualsNet.com

 search engine

Содержание WeatherMaster 48HC Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды