Carrier Taylor 632 Скачать руководство пользователя страница 27

Страница: 27 / 50

Model 632

Operating Procedures

Priming

Step 1

With a pail beneath the door spout, open the draw

handle. Be sure the prime plug is still in the UP position

(soft serve side only). Pour two gallons (7.6 liters) of
fresh mix into the mix hopper and allow it to flow into

the freezing cylinder. This will force out any remaining

sanitizing solution. When full strength mix is flowing

from the door spout, close the draw handle.

Note:

Use only

fresh

mix when priming the freezing

cylinder.

Figure 36

Step 2

Once a

steady

stream of mix starts to flow from the

prime plug opening in the bottom of the freezer door,

push down the prime plug (soft serve only).

Figure 37

Step 3

Lubricate the o--rings on the air tube on the end with

the small hole on the side (soft serve only).

Step 4

Install the air tube (the end with the hole) with the air

orifice installed into the mix inlet hole in the mix hopper

(soft serve only).

Figure 38

Step 5

Press the AUTO key. The AUTO light will come on

indicating the main refrigeration system is operating.

When the unit cycles off, the product will be at serving

viscosity.

Note:

The MIX REF light will come on, indicating the

mix refrigeration system is operating to maintain the

mix in the mix hopper.

Figure 39

Step 6

Fill the hopper with mix. As the mix level comes in

contact with the mix level sensing probe on the rear

wall of the hopper, the MIX LOW light will shut off.

Step 7

Place the mix hopper cover in position over the mix

hopper.

Repeat steps 1 through 7

for the other side of the

freezer.

Содержание Taylor 632



















































Результаты поиска

Содержание Taylor 632

Отзывы:

Похожие инструкции для Taylor 632

Бренды по названию

Популярные бренды

Carrier Taylor 632, Руководство по эксплуатации

Результаты поиска

Содержание Taylor 632

Отзывы:

Похожие инструкции для Taylor 632

Бренды по названию

Популярные бренды