Carrier PG80MSU Скачать руководство пользователя

Страница: 4 / 40

PG80MSU: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

INTRODUCTION

A220905

Fig. 2 – Clearances to Combustibles

A02097

Fig. 3 – Multipoise Orientations

This 4-way multipoise Category I fan-assisted furnace is CSA

design-certified. A Category I fan-assisted furnace is an appliance

equipped with an integral mechanical means to either draw or force

products of combustion through the combustion chamber and/or heat

exchanger. The furnace is factory-shipped for use with natural gas.
This furnace is not approved for installation in mobile homes,

recreational vehicles, or outdoors. The furnace is not permitted to be

used for heating of buildings under construction. This furnace is

designed for minimum continuous return-air temperature of 60°F

(16°C)db or intermittent operation down to 55°F (13°C) db such as when

used with a night setback thermostat. Return-air temperature must not

exceed 80°F (27°C) db. Failure to follow these return-air temperature

limits may affect reliability of heat exchangers, motors, and controls, see

Fig. 4

For accessory installation details, refer to the applicable instruction

literature.

NOTE:

Remove all shipping brackets and materials before operating the

furnace.

A221115

Fig. 4 – Return Air Temperature

A02054

Fig. 5 – Prohibit Installation on Back

A93044

Fig. 6 – Installation in a Garage

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

Do not install the furnace on its back or hang furnace with control

compartment facing downward. Safety control operation will be

adversely affected. Never connect return-air ducts to the back of the

furnace. See

Fig. 5

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death,

and/or property damage.

When the furnace is installed in a residential garage, the burners and

ignition sources must be located at least 18 inches above the floor, see

Fig. 6

. The furnace must be located or protected to avoid damage by

vehicles. When the furnace is installed in a public garage, airplane

hangar, or other building having a hazardous atmosphere, the furnace

must be installed in accordance with the NFGC.

Содержание PG80MSU









































Результаты поиска

Содержание PG80MSU

Отзывы:

Похожие инструкции для PG80MSU

Бренды по названию

Популярные бренды

Carrier PG80MSU, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание PG80MSU

Отзывы:

Похожие инструкции для PG80MSU

Бренды по названию

Популярные бренды