background image

Step 4—Blower Removal

To remove blower from furnace:

1. Turn off all oil and electrical supplies upstream of furnace.

2. Remove burner access door and blower access door.

3. Remove the blower retaining screw (on blower shelf).

4. Remove cover from control box and disconnect thermostat

and power wires from board.

5. Slide blower forward on rails toward front of unit.

6. Reverse items 1 through 5 to reinstall blower. Refer to wiring

diagram (Fig. 3 or Fig. 4) of these instructions or diagram
located on inside of blower door to properly rewire unit.

A94328

SERVICE TRAINING

Packaged Service Training programs are an excellent way to increase your 
knowledge of the equipment discussed in this manual, including:

• Unit Familiarization

• Maintenance

• Installation Overview

• Operating Sequence

A large selection of product, theory, and skills programs is available, using popular 
video-based formats and materials.  All include video and/or slides, plus companion 
book.

Classroom Service Training plus "hands-on" the products in our labs can mean 
increased confidence that really pays dividends in faster troubleshooting, fewer 
callbacks.  Course descriptions and schedules are in our catalog.

CALL  FOR  FREE  CATALOG  1-800-962-9212

[  ] Packaged Service Training

[  ] Classroom Service Training

Copyright 1998 CARRIER Corp. • 7310 W. Morris St. • Indianapolis, IN 46231

58cma2si

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Book 1

4

Tab

6a 8a

PC 101

Catalog No. 535-892

Printed in U.S.A.

Form 58CMA-2SI

Pg 12

1-98

Replaces: 58CMA-1SI

Содержание OIL FURNACE 58CMA













Отзывы: