manualshive.com logo in svg

Carrier NSB-10K-2-I-2-BB2, Инструкция по установке и эксплуатации, Страница: 7 / 7

Поделиться
Скачать
Carrier NSB-10K-2-I-2-BB2 Скачать руководство пользователя страница 7

Specifications subject to change without notice.

 

7 of 7

 

Immersion Temperature Sensors 

 

Installation and Operation

 

Catalog No. 11-808-632-01

 

 

 

 

 

#20907 – 

2/20/19

 

 

Wiring & Termination 

 

Carrier recommends using twisted pair of at least 22AWG and sealant filled connectors for all wire connections. Larger gauge wire 
may be required for long runs. All wiring must comply with the National Electric Code (NEC) and local codes. Do NOT run this device’s 
wiring in the same conduit as high or low voltage AC power wiring. Tests show that inaccurate signal levels are possible when AC 
power wiring is present in the same conduit as the sensor wires.

 

 
 
 
 
 
 
 
 

 
 

Diagnostics 

 

Problems:

 

Controller reports higher or lower 
than actual temperature.

 

Possible Solutions:

 

- 

Confirm the input is set up correctly in the front end software

 

- 

Check wiring for proper termination and continuity (shorted or open).

 

- 

Disconnect wires and measure sensor resistance and verify the “Sensor” output is correct. 

 

Thermistor 

Sensor

 

To Controller 
Analog Input (AI) 
(No Polarity)

 

To Controller Analog 
Input (AI) (No 
Polarity)

 

     Figure 14: 

2 Wire Lead Wire Termination for Thermistor 

 

Содержание NSB-10K-2-I-2-BB2








Отзывы:

Нет отзывов