manualshive.com logo in svg

Carrier NSB-10K-2-I-2-BB2, Инструкция по установке и эксплуатации, Страница: 5 / 7

Поделиться
Скачать
Carrier NSB-10K-2-I-2-BB2 Скачать руководство пользователя страница 5

Immersion Temperature Sensors 

 

Installation and Operation

 

Specifications subject to change without notice.

 

5 of 7

 

Catalog No. 11-808-632-01

 

 

 

 

#20907 – 

2/20/19

 

 

Thermowell Installation (continued…) 

 

 

Pipes less than 3 inches in diameter

 

 

T- Mount

 

Figure 7 shows how a 2” tee and a ½” to 2” bushing 
allows a 2” thermowelll to measure the temperature of the 
contents of a 2” water pipe. 
 
Be sure to use a thread sealant on the outside threads of 
the thermowell. 
 
 
 
 
 
 
 
 

Corner  Mount

 

Figure 8 shows how a pipe tee can be used in an elbow 
application. A 2” tee and a ½” to 2” bushing allows a 4” 
thermowell to measure the temperature of the contents of 
a 2” water pipe. 

NOTE

  Temperatures in pipes as small as 1-1/4” may be 

measured by this method. In small pipes, the diameter of 
the thermowell may become a significant obstruction, so 
be sure to check for proper flow rates after installation is 
complete. 

 

 
 
 
 
 
 
 
 
 
 
 

Figure 7: 

Typical T-Mount

 

 
 
 
 
 
 
 
 
 
 
 
 

Figure 8: 

Typical Corner Mount 

 

Immersion Sensor Installation 

 

 

 

Immersion probes come with a plastic fitting that 
screws into the threads of the thermowell.  

Pull the immersion probe away from the plastic fitting 
until the probe is fullly extended. Insert the probe into 
the thermowell until the plastic fittings come into contact 
with the threads in the thermowell. Hand tighten the 
immersion sensor snugly into the thermowell without 
too much torque. The temperature probe slides back 
into the enclosure as the sensor contacts the end of the 
thermowell.

 

Make sure that the tip of the immersion sensor probe is 
in good contact with the bottom of the thermowell by 
pushing on the flaired end of the probe until the tip 
bottoms out in the thermowell.

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 

Figure 9: 

Immersion Sensor Before Insertion

 

* As the immersion sensor is hand-threaded into the thermowell, the flair end of the 
probe will be pushed into the enclosure as the probe tip bottoms out in the 
thermowell. The probe can slide up to 1.6”. The Junction Box enclosure is shown 
above but the process is the same for the other enclosure styles.

 

 
 

 

 

 

 
 

 

T-pipe fitting

 

Reducer

 

1/2 inch NPT

 

T-pipe fitting

 

Reducer

 

1/2 inch NPT

 

Length Per Order

 

*Sensor Slides

 

1. 

Pull Sensor to 

Extend Fully

 

2. 

Insert

 

3. 

Hand Tighten

 

Содержание NSB-10K-2-I-2-BB2








Отзывы:

Нет отзывов