Carrier N92ESN Скачать руководство пользователя

Страница: 24 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

115-V Wiring

Furnace must have a 115-v power supply properly connected and

grounded.

NOTE:

Proper polarity must be maintained for 115-v wiring. If polarity

is incorrect, control LED status indicator light will flashes rapidly

(Status Code 10) and furnace will

NOT

operate.

Verify that the voltage, frequency, and phase correspond to that specified

on unit rating plate. Also, check to be sure that service provided by

utility is sufficient to handle load imposed by this equipment. Refer to

rating plate or

Table 10

for equipment electrical specifications.

U.S.A. Installations

: Make all electrical connections in accordance with

the current edition of the National Electrical Code (NEC) NFPA 70 and

any local codes or ordinances that might apply.

Canada Installations

: Make all electrical connections in accordance

with the current edition of the Canadian Electrical Code CSA C22.1 and

any local codes or ordinances that might apply.
Use a separate, fused branch electrical circuit with a properly sized fuse

or circuit breaker for this furnace. See

Table 10

for wire size and fuse

specifications. A readily accessible means of electrical disconnect must

be located within sight of the furnace.

A190079

Fig. 32 – Typical Single-Stage Wiring Diagram

A190279

Fig. 33 – Field-Supplied External Electrical Box on Furnace Casing

Table 10 – Electrical Data

J-Box Installation

The J-Box must be used when field line voltage electrical connections

are made to the furnace wiring harness inside the furnace casing. The

J-Box cover is not required if a field-supplied external electrical box is

attached to the outside of the furnace casing. The field ground wire and

furnace main ground wire are grounded when the J-Box bracket is

attached to the furnace and the field ground wire and factory ground wire

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death, or

property damage.

Do not connect aluminum wire between disconnect switch and furnace.

Use only copper wire. See

Fig. 35

115-V FIELD-

SUPPLIED

DISCONNECT

AUXILIARY
J-BOX

24-V

TERMINAL

BLOCK

THREE-WIRE

HEATING-ONLY

FIVE WIRE

NOTE 1

NOTE 2

FIELD-SUPPLIED
DISCONNECT

CONDENSING
UNIT

TWO
WIRE

FURNACE

C
O
N
T
R
O

COM

GND

FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING

208/230- OR
460-V
THREE
PHASE

208/230-V
SINGLE
PHASE

BLOWER DOOR SWITCH

WHT

BLK

WHT

BLK

NOTES:

Connect Y-terminal in furnace as shown for proper blower operation.
Some thermostats require a "C" terminal connection as shown.
If any of the original wire, as supplied, must be replaced, use
same type or equivalent wire.

GND

THERMOSTAT
TERMINALS

1.
2.
3.

COPPER

WIRE ONLY

ELECTRIC

DISCONNECT

SWITCH

ALUMINUM

WIRE

FURNACE SIZE

VOLTS-

HERTZ-

PHASE

OPERATING VOLTAGE

RANGE

*. Permissible limits of the voltage range at which the unit operates satisfactorily.

MAXIMUM

UNIT

AMPS

UNIT

AMPACITY

†

†. Unit ampacity = 125 percent of largest operating component’s full load amps plus 100 percent of all other potential operating components’ (EAC, humidifier, etc.) full load amps

MINIMUM

WIRE SIZE

AWG

MAXIMUM

WIRE

LENGTH

FT (M)

‡

‡. Time-delay type is recommended.

MAXIMUM

FUSE OR CKT

BKR AMPS