Carrier N8MXL Скачать руководство пользователя

Страница: 6 / 50

Specifications are subject to change without notice.

441 01 1422 00

THE BLOWER IS LOCATED

TO THE RIGHT OF THE

BURNER SECTION, AND

AIR CONDITIONED AIR IS

DISCHARGED TO THE LEFT.

THE BLOWER IS

LOCATED BELOW THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED UPWARD.

THE BLOWER IS

LOCATED ABOVE THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED DOWNWARD

THE BLOWER IS

LOCATED TO THE LEFT

OF THE BURNER SECTION,

AND CONDITIONED AIR IS

DISCHARGED TO THE RIGHT.

A02097

Fig. 4

−

Multipoise Orientations

LOCATION

GENERAL

This multipoise furnace is shipped in packaged configuration.

Some assembly and modifications are required when used in any

of the four applications shown in Fig. 4.
This furnace must:

be installed so the electrical components are protected
from water.

not be installed directly on any combustible material
other than wood flooring for upflow applications.

Downflow installations require use of a factory

−

ap-

proved floor base or coil assembly when installed on

combustible materials or wood flooring (refer to

SAFETY CONSIDERATIONS).

be located as close to the chimney or vent and attached
to an air distribution system. Refer to Air Ducts section.

be provided ample space for servicing and cleaning.
Always comply with minimum fire protection clear-

ances shown on the furnace clearance to combustible

label.

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal

injury or death, and unit component damage.
Corrosive or contaminated air may cause failure of parts

containing flue gas, which could leak into the living space.

Air for combustion must not be contaminated by halogen

compounds, which include fluoride, chloride, bromide, and

iodide. These elements can corrode heat exchangers and

shorten furnace life. Air contaminants are found in aerosol

sprays, detergents, bleaches, cleaning solvents, salts, air

fresheners, and other household products. Do not install

furnace in a corrosive or contaminated atmosphere. Make

sure all combustion and circulating air requirements are met,

in addition to all local codes and ordinances.

WARNING

The following types of furnace installations may require

OUTDOOR AIR for combustion due to chemical exposures:

Commercial buildings

Buildings with indoor pools

Laundry rooms

Hobby or craft rooms, and

Chemical storage areas

If air is exposed to the following substances, it should not be used

for combustion air, and outdoor air may be required for

combustion:

Permanent wave solutions

Chlorinated waxes and cleaners

Chlorine based swimming pool chemicals

Water softening chemicals

−

icing salts or chemicals

Carbon tetrachloride

Halogen type refrigerants

Cleaning solvents (such as perchloroethylene)

Printing inks, paint removers, varnishes, etc.

Hydrochloric acid

Cements and glues

Antistatic fabric softeners for clothes dryers

Masonry acid washing materials

Содержание N8MXL


















































Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды

Carrier N8MXL, Руководство по установке

Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды