Carrier N8MXL Скачать руководство пользователя страница 42

Страница: 42 / 50

Specifications are subject to change without notice.

441 01 1422 00

CLEANING AND/OR REPLACING AIR FILTER

The air filter arrangement will vary depending on the application.

The filter is exterior to the furnace casing.

NOTE

: If the filter has an airflow direction arrow, the arrow

must point towards the blower.

Table 14 – Filter Size Information (In. / mm)

FURNACE

CASING

WIDTH

In. (mm)

FILTER SIZE (In. / mm)

FILTER TYPE

Side Return

Bottom Return

14-1/2

(368)

16 x 25 x 3/4

(406 x 635 x 19)

14 x 25 x 3/4

(356 x 635 x 19)

Washable*

17-1/2

(445)

16 X 25 X 3/4

(406 x 635 x 19)

16 X 25 X 3/4

(406 x 635 x 19)

Washable*

21 (533)

16 x 25 x 3/4

(406 x 635 x 19)

20 X 25 X 3/4

(508 x 635 x 19)

Washable*

24 (610)

16 x 25 x 3/4

(406 x 635 x 19)

24 X 25 X 3/4

(610 x 635 x 19)

Washable*

* Recommended

BLOWER MOTOR AND WHEEL

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.
Blower access door switch opens 115

−

v power to control.

No component operation can occur unless switch is closed.

Caution must be taken when manually closing this switch

for service purposes.

WARNING

NOTE

: The blower wheel should not be dropped or bent as

balance will be affected. The following steps should be performed
by a qualified service agency.
To ensure long life and high efficiency, clean accumulated dirt

and grease from blower wheel and motor annually.
The inducer and blower motors are pre

−

lubricated and require no

additional lubrication. These motors can be identified by the

absence of oil ports on each end of the motor.
Clean blower motor and wheel as follows:

1. Turn off electrical supply to furnace.
2. Remove outer door.
3. For downflow or horizontal furnaces having vent pipes

within the furnace that pass in front of the blower access

door:

a. Disconnect vent connector from furnace vent elbow.

b. Disconnect and remove short piece of vent pipe from

within furnace.

4. Remove two screws from blower access door and remove

blower access door.

5. All factory wires can be left connected, but field thermo-

stat connections may need to be disconnected depending

on their length and routing.

6. Remove two screws holding blower assembly to blower

deck and slide blower assembly out of furnace.

7. Clean blower wheel and motor using a vacuum with soft

brush attachment. Blower wheel blades may be cleaned

with a small paint or flux brush. Do not remove or disturb

balance weights (clips) on blower wheel blades.

8. Vacuum any loose dust from blower housing, wheel and

motor.

9. If a greasy residue is present on blower wheel, remove

wheel from the blower housing and wash it with an appro-

priate degreaser. To remove wheel:

NOTE

: Before disassembly, mark blower motor, and blower

housing so motor and each arm is positioned at the same location
during reassembly.

a. Disconnect power choke wires (if used) and ground wire

attached to blower housing.

b. Remove screws securing cutoff plate and remove cutoff

plate from housing.

c. Loosen set screw holding blower wheel on motor shaft

(160+/

−

20 in.

−

lb. when reassembling).

d. Remove bolts holding motor to blower housing and slide

motor out of wheel (40+/

−

10 in.

−

lb. when reassembling).

e. Remove blower wheel from housing.

f. Clean wheel and housing.

10. Reassemble motor and blower by reversing steps 9f

through 11a, finishing with 9a. Be sure to reattach ground

wire to the blower housing.

11. Verify that blower wheel is centered in blower housing

and set screw contacts the flat portion of the motor shaft.

Loosen set screw on blower wheel and reposition if neces-

sary.

12. Spin the blower wheel by hand to verify that the wheel

does not rub on the housing.

13. Reinstall blower assembly in furnace.
14. Reinstall two screws securing blower assembly to blower

deck.

UNIT DAMAGE HAZARD

Failure to follow this caution may result in shortened heat

exchanger life.
Heating fan speed(s) MUST be adjusted to provide proper

air temperature rise as specified on the rating plate.

Recommended operation is at the midpoint of the rise range

or slightly above. Refer to “SET TEMPERATURE RISE”

under START

−

UP, ADJUSTMENT, and SAFETY

CHECK.

CAUTION

NOTE

: Refer to Table 5 for motor speed lead relocation if leads

were not identified before disconnection.

15. Refer to furnace

wiring diagram, and connect thermostat

leads if previously

disconnected.

16. To check blower for proper rotation:

a. Turn on electrical supply.

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal

injury, or death.
Blower access door switch opens 115

−

v power to

furnace control. No component operation can occur

unless switch is closed. Exercise caution to avoid

electrical shock from exposed electrical components

when manually closing this switch for service purposes.

WARNING

b. Manually close blower access door switch.

Содержание N8MXL


















































Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды

Carrier N8MXL, Руководство по установке

Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды