background image

10

4. If the unit ductwork is to be attached to vertical opening

flanges on the unit base (jackstand applications only), do so

at this time.

PROPERTY DAMAGE HAZARD

Failure to follow this caution may result in property damage.
Collect ALL screws that were removed. DO NOT leave screws

on rooftop as permanent damage to the roof may occur.

!

CAUTION

5. It is recommended that the base insulation around the peri-

meter of the vertical return--air opening be secured to the
base with aluminum tape. Applicable local codes may

require aluminum tape to prevent exposed fiberglass.

6. Reinstall horizontal duct covers. Ensure opening is air-- and

watertight.

7. After completing unit conversion, perform all safety checks

and power up unit.

NOTE

: The design and installation of the duct system must be in

accordance with the standards of the NFPA for installation of non
residence--type air conditioning and ventilating systems, NFPA
90A or residence--type, NFPA 90B; and/or local codes and
ordinances.

Provide for Condensate Disposal

NOTE

: Ensure that condensate--water disposal methods comply

with local codes, restrictions, and practices.
The units dispose of condensate through a 3/4 --in. NPT female

fitting that exits on the compressor end of the unit. Condensate

water can be drained directly onto the roof in rooftop installations
(where permitted) or onto a gravel apron in ground level

installations. Install a field--supplied condensate trap at end of
condensate connection to ensure proper drainage. Make sure that

the outlet of the trap is at least 1 in. (25 mm) lower than the
drain--pan condensate connection to prevent the pan from

overflowing. Prime the trap with water. When using a gravel apron,

make sure it slopes away from the unit.
If the installation requires draining the condensate water away from

the unit, install a field--supplied 2--in. (51 mm) trap at the
condensate connection to ensure proper drainage. Condensate trap

is available as an accessory or is field--supplied. Make sure that the

outlet of the trap is at least 1 in. (25 mm) lower than the unit
drain--pan condensate connection to prevent the pan from

overflowing. Connect a drain tube using a minimum of
field--supplied 3/4 --in. PVC or field--supplied 3/4 --in. copper pipe

at outlet end of the 2 --in. (51 mm) trap (See Fig. 10). Do not

undersize the tube. Pitch the drain tube downward at a slope of at
least 1 in. (25 mm) for every 10 ft (3 m) of horizontal run. Be sure

to check the drain trough for leaks. Prime the trap at the beginning
of the cooling season start--up.

Install Flue Hood

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal

injury or death.
The venting system is designed to ensure proper venting.

The flue hood assembly must be installed as indicated in

this section of the unit installation instructions.

!

WARNING

Install the flue hood as follows:

1. This installation must conform with local building codes

and with the National Fuel Gas Code (NFGC), NFPA 54
/ANSI Z223.1--2006 (in Canada, CAN/CSA B149.1, and

B149.2) latest revision. Refer to provincial and local
plumbing or wastewater codes and other applicable local
codes.

2. Remove flue hood from shipping location (inside the return

section of the blower compartment--See Fig. 8). Remove the

return duct cover to locate the flue hood. Remove two
screws on flue panel. Place flue hood assembly over flue
panel. Orient screw holes in flue hood with holes in the flue

panel.

3. Secure flue hood to flue panel by inserting a single screw on

the top and the bottom of the hood.

Horizontal Duct Covers

A09076

Basepan
Downflow
(Vertical)
Supply
Knockout 

Basepan
Downflow 
(Vertical)
Return
Knockout 

A09077

Fig. 8 -- Supply and Return Duct Opening

48X

T

--

A

Содержание INFINITIR 15 SEER 48XT-A







































Отзывы: