GB - 5
HDB - IR
E N G L I S H
M
V
V
25 mm
0,984 in
5 mm 0,196
in
System configuration
The unit settings are made at the factory (refer to the specific
instruction sheet).
In the case of system installation other than the original one (as
referred to in the specific instruction sheet) the factory configuration
must be changed.
Such operation must be performed by the installer as follows:
Configuration of the System
• Check all electrical connections (instructions and wiring diagram).
• Insert the batteries into the remote control and leave it OFF.
• Energise the system, turning the power supply ON.
• Press the and
buttons of the infrared remote control and
hold them pressed for more than 5 seconds.
• The display will be cleared, the time segments will display the first
configuration item (rAdr = remote address) and the temperature
segments will display the default value of this configuration item
(Ab = control of both indoor units).
• Press button repeatedly until the written one of the menu you
want to change appears on the screen.
• Press either the or button to change the default value.
• Press the
button to send the configuration to the unit.
• Press button to leave the configuration menu.
For other available configuration options, see table I.
Note:
When 30 seconds have elapsed and no buttons have been pressed,
the remote controller will automatically exit the configuration menu
and the procedure has to be restarted.
Configuration of the remote controller
• Insert the batteries into the remote controller and leave it OFF.
• Press the and
buttons of the infrared remote control and
hold them pressed for more than 5 seconds.
• The display will be cleared, the temperature segments will display
the first configuration item (CH = remote address) and the time
segments will display the default value of this configuration item
(Ab = control of both indoor units).
• Press button repeatedly until “rc” is displayed.
• Press either the or button to change the default value (HP)
to the new value (CO).
• Press the
button to send the configuration to the unit, which
will confirm with a “beep”.
• Press button to save the new remote control configuration.
For other available configuration options, see table II.
Note:
When 30 seconds have elapsed and no buttons have been pressed,
the remote controller will automatically exit the configuration menu
and the procedure has to be restarted.
wall-mounted bracket
System configuration
Содержание HDB
