Carrier Gemini 38AU07 Series Скачать руководство пользователя | Manualshive

Страница: 41 / 52

background image

41

APPENDIX A — AIR CONDITIONER AND HEAT PUMP WITH PURON

®

QUICK REFERENCE GUIDE

• Puron (R-410A) refrigerant operates at 50 percent to 70

percent higher pressures than R-22. Be sure that servic-

ing equipment and replacement components are designed

to operate with Puron refrigerant.

• Puron refrigerant cylinders are rose colored.
• Recovery cylinder service pressure rating must be 400

psig, DOT 4BA400 or DOT BW400.

• Puron systems should be charged with liquid refrigerant.

Use a commercial type metering device in the manifold

hose when charging into suction line with compressor

operating.

• Manifold sets should be 700 psig high side and 180 psig

low side with 550 psig low-side retard.

• Use hoses with 700 psig service pressure rating.
• Leak detectors should be designed to detect HFC refrig-

erant.

• Puron, as with other HFCs, is only compatible with POE

oils.

• Vacuum pumps will not remove moisture from oil.
• Use only factory specified liquid-line filter driers with

rated working pressures greater than 600 psig.

• Do not install a suction-line filter drier in liquid-line.
• POE oils absorb moisture rapidly. Do not expose oil to

atmosphere.

• POE oils may cause damage to certain plastics and roof-

ing materials.

• Wrap all filter driers and service valves with wet cloth

when brazing.

• A factory approved, liquid-line filter drier is required on

every unit.

• Do not use an R-22 TXV.
• If indoor unit is equipped with a TXV, it must be changed

to a Puron TXV.

• Never open system to atmosphere while it is under a vac-

uum.

• When system must be opened for service, recover refrig-

erant, break vacuum with dry nitrogen before opening

system.

• Always replace filter drier after opening system for ser-

vice.

• Do not vent Puron refrigerant into the atmosphere.
• Do not use capillary tube coils.
• Observe all warnings, cautions, and bold text.
• All Puron heat pumps must have indoor TXV.
• Do not leave Puron suction line driers in place for more

than 72 hours.

«
...
39
40
41
42
43
...
»

Содержание Gemini 38AU07 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Gemini 38AU07 Series

Altherma EHVZ04S18DA6V

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 8

Altherma EAVZ16S18DA6V

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 56

altherma EJHA04AAV3

Бренд: Daikin Страницы: 16

Бренд: YAMADA Страницы: 84

Бренд: Wacker Neuson Страницы: 44

Бренд: YUKEN KOGYO Страницы: 82

Бренд: Tebas Страницы: 14

Бренд: York Страницы: 90

Бренд: UNITED Страницы: 4

Бренд: Ariston Страницы: 88

Бренд: Dex Страницы: 24

Бренд: Enerpac Страницы: 40

Бренд: Graco Страницы: 20

Бренд: Olimpia splendid Страницы: 12

Бренд: TapFlo Страницы: 69

Бренд: Ariston Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды