manualshive.com logo in svg

Carrier FX4D 019, Руководство по установке, Страница: 4 / 10

Поделиться
Скачать
Carrier FX4D 019 Скачать руководство пользователя страница 4

FX4D: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

4

A03001

Fig. 5 – Conversion for Horizontal Right Applications - Slope Coil

A00071A

Fig. 6 – Conversion for Horizontal Right Applications - A-Coil

A07571

Fig. 7 – Drain Pan Support Bracket

MANUFACTURED HOUSING AND MOBILE HOME 

APPLICATIONS

1. Fan coil unit must be secured to the structure using field-supplied

hardware.

2. Allow  a  minimum  of  24  inches  (610mm)  clearance  from  access

panels.

3. Recommended method of securing for typical applications:

a. If fan coil is away from wall, attach pipe strap to top of fan coil 

using No. 10 self tapping screws. Angle strap down and away 

from back of fan coil, remove all slack, and fasten to wall stud of 

structure using 5/16” lag screws. Typically both sides of the fan 

coil. 

b. If fan coil is against wall, secure fan coil to wall stud using 1/8” 

(3mm) wide right-angle brackets. Attach brackets to fan coil 

using No. 10 self tapping screws and to wall stud using 5/16” lag 

screws (refer to Fig. 8).

COIL MOUNTING
SCREW

BLOWER 
ASSEMBLY

REFRIGERANT
CONNECTIONS

SECONDARY DRAIN

PRIMARY DRAIN

DRAINPAN

SLOPE COIL

SKI

COIL

SUPPORT 

RAIL

COIL

SUPPORT

RAIL

COIL

BRACKET

DRAIN PAN

SUPPORT

BRACKET

COIL

SUPPORT

RAIL

COIL

BRACKET

HORIZONTAL

DRAIN PAN

PRIMARY DRAIN

HORIZONTAL RIGHT

SECONDARY DRAIN

HORIZONTAL RIGHT

REFRIGERANT

CONNECTIONS

AIR SEAL
ASSEMBLY

A

B

C

HORIZONTAL

RIGHT

APPLICATION

DRAIN PAN

SUPPORT BRACKET

Содержание FX4D 019











Отзывы:

Нет отзывов