background image

Air Purifier Sizes 1620, 1625, 2020, 2025, 2420: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

9

A11497

Fig. 17 – Attach Logo

Checking Air Purifier Operation

1. Attach the air purifier door to the cabinet. The power supply will

not energize the air purifier if the door is not properly in place.

2. Turn  the  HVAC  system  power  on  and  adjust  the  thermostat  or

System Control to activate the system fan.

3. Turn the air purifier power switch to on position.
4. The green indicator light above the air purifier power switch should

illuminate (

Fig. 18

).

5. This green indicator light will illuminate when the air purifier door

is  installed,  the  power  switch  is  in  the  ON  position  AND  the

furnace blower is running. If a flow sensor (model KIT160000) is

installed  in  the  air  purifier  and  there  is  no  airflow,  the  green

indicator light will blink slowly (once every 3 seconds) indicating

that the air purifier is in STANDBY mode. If a flow sensor is not

installed, the green indication light should go off when the blower

stops running.

For information on the green indicator light status and error conditions,

See 

Table 1

 for status codes or 

Table 2

 for error codes in section Error

and Status Codes.

A11369

Fig. 18 – Power Indicator (Green LED)

Control

When the air purifier is used with a Communicating Wall Control, the

Control can be configured to remind the homeowner when it is time to

change  the  air  purifier  cartridge.  This  maintenance  reminder  can  be

based  on  either  the  TrueSense™  dirty  filter  algorithm  or  time.  The

installer should use their discretion to select the most appropriate option

based on the initial system static pressure. 

Maximizing Performance

Maximum  air  purification  performance  is  obtained  when  the  furnace

blower is set for continuous operation on the thermostat or Control.

MAINTENANCE

The  air  purifier  is  designed  to  require  minimal  maintenance.

Maintenance is limited to the periodic replacement of the air purification

cartridge  and  inspection/brush  cleaning  of  the  ionization  array.

Frequency  of  air  purifier  cartridge  replacement  and  cleaning  of  the

ionization  array  may  vary  depending  on  ductwork  design  and  local

environmental conditions, generally 6-9 months.

WARNING

!

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.

Before installing or servicing system,  always turn  off main power to

system. There may be more than one disconnect switch. Lock out and

tag switch with a suitable warning label.

WARNING

!

CARBON MONOXIDE HAZARD

Failure to follow this warning could result in personal injury or death.

Do not remove door during blower operation or operate blower with

door removed or improperly latched.

WARNING

!

FIRE HAZARD

Failure  to  follow  this  warning  could  result  in  personal  injury  or

equipment damage.

Use of non-factory approved filter cartridge will void the warranty and

may cause damage due to fire.

This  equipment  should  be  inspected  frequently  and  collected  dirt

removed regularly to prevent excessive accumulation that may result in

flash-over or fire damage.

Green Power
Indicator

Содержание DGAPAXX 1620














Отзывы: