background image

Air Purifier Sizes 1620, 1625, 2020, 2025, 2420: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

11

A11370

Fig. 19 – Removal of Deposits from Ionization Pins

ERROR AND STATUS CODES

The error codes and status codes are shown in the following tables.

The green indicator light on door cover shown in 

Fig. 18

, Power Indication (Green LED).

Table 2 – Operating Status Codes

INDICATOR LIGHT CODE

 EXPLANATION

POSSIBLE CAUSE

RECOMMENDED ACTION

OFF

No incoming AC power to

air purifier control electronics

Normal operation when airflow is not 

present for models without flow sensor 

due to AC power to purifier being off at 

furnace control board (EAC terminals).

ON/OFF power switch turned to OFF

Turn purifier power switch to ON 

position

Power to entire system is off

(furnace and air purifier).

Check that the HVAC system is 

switched on.

Blown fuse or tripped circuit

breaker for HVAC system

Replace fuse or reset circuit

breaker. Call for service if problem 

reoccurs.

Misaligned or damaged purifier door

Insure that door is undamaged and 

properly installed on purifier

cabinet.

Damaged or disconnected

incoming power wiring 

Call for service

ON (continuously)

Air purifier on

Normal operation when airflow is 

present.

FLASHING

(1 flash every 4 seconds)

Standby Mode

Normal operation when airflow is not 

present for models with flow sensor.

Ions detected in airflow due to missing 

replaceable filter element

Place filter in air purifier.

Debris is covering airflow sensor (for 

models including an airflow sensor).

Make sure flow sensor is clean and 

unobstructed

Flow sensor is damaged (for

models including an airflow sensor).

Replace flow sensor, available as 

replacement kit (KIT160000).

Flow sensor bypass assembly is 

damaged (for models without an airflow 

sensor).

Replace flow sensor bypass

assembly, available as

replacement kit (KIT161000).

One or more of the three airflow sensor 

contact springs on purifier cabinet 

downstream rail are bent or damaged.

Replace flow sensor contact spring 

assembly, included as part of the flow 

sensor kits (KIT160000 and flow 

sensor bypass kit KIT161000).

Top View

30°

POINTS ARE SHARP! BE VERY CAREFUL DURING CLEANING.

Tip of point with residue

Tip of point after cleaning

Содержание DGAPAXX 1620














Отзывы: