background image

17

NOTES:

1. Table 9 illustrates the complete hierarchy. Menu parameters may 

be different depending on configuration. For example, none of the 

DCV parameters appear for a system that does not have a DCV

 

(CO

2

) sensor.

2. When values are displayed, pressing and holding the 

 

or 

button causes the display to automatically increment.

3. ERV Operation: When in Cooling mode AND the conditions are 

NOT OK for economizing - the ERV terminal will be energized. In 

the Heating mode the ERV terminal will be energized when the OA

 

is below the ERV OAT set point in the set point menu.

ALARMS(_)

Alarms display only when they are active. The menu title “ALARMS(_)” includes the number of active alarms in parentheses ( ). When using 

SYLK bus sensors, “SYLK” will appear on the screen, and when using 20k OA temperature sensors, “SENS T” will appear on the screen

MA T SENS ERR

n/a

n/a

MIXED AIR TEMPERATURE SENSOR ERROR

Mixed air sensor has failed or become disconnected - check wiring then replace 

sensor if the alarm continues.

CO2 SENS ERR

n/a

n/a

CO

2

 SENSOR ERROR

CO

2

 sensor has failed, gone out of range or become disconnected - check wiring, 

then replace sensor if the alarm continues.

OA SENS T ERR

n/a

n/a

OUTSIDE AIR TEMPERATURE SENSOR ERROR

Outdoor-air temperature sensor has failed or become disconnected - check wiring 

(OAT sensor connected at input terminals OAT), then replace if the alarm continues.

OA SYLK SENS ERR

n/a

n/a

OUTSIDE AIR ENTHALPY SENSOR ERROR

OAT sensor connected on S-bus.

DA T SENS ERR

n/a

n/a

DISCHARGE AIR TEMPERATURE SENSOR ERROR

SYS ALARM

n/a

n/a

When AUX1-O is set to SYS and there is any alarm (e.g., failed sensors, etc.), the 

AUX1-O terminal has 24 vac out.

ACT UNDER V

n/a

n/a

ACTUATOR VOLTAGE LOW

Voltage received by Actuator is below expected range.

ACT OVER V

n/a

n/a

ACTUATOR VOLTAGE HIGH

Voltage received by Actuator is over expected range.

ACT STALLED

n/a

n/a

ACTUATOR STALLED

Actuator stopped before achieving commanded position.

Table 9 — Menu Structure

(cont) 

MENU

PARAMETER

PARAMETER

DEFAULT

VALUE

PARAMETER

RANGE AND 

INCREMENT

2

NOTES

LEGEND

n/a

— Not Applicable

DCV

— Demand Controlled Ventilation

ERV

— Energy Recovery Ventilation

HP

— Heat  Pump

LC

— Liquid Crystal

LCD

— Liquid Crystal Display

MA

— Mixed  Air

MAT

— Mixed Air Temperature Sensor

O/A

— Outdoor Air

OAT

— Outdoor Air Temperature Sensor

OCC

— Occupied

R/A

— Return Air

RAT

— Return Air Temperature

RH

— Relative Humidity

RTU

— Rooftop Unit

Содержание CRECOMZR085A00





















Отзывы: