Carrier Creat-ion 38KHET30-708F Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 54

Carrier Creat-ion 38KHET30-708F Скачать руководство пользователя страница 43

41

CONNECTING ELECTRICAL WIRING (Cont.)

18-4 CONNECTING ELECTRICAL WIRING TO OUTDOOR UNIT

connect electrical cables to the terminal block of outdoor unit as per the wiring diagram
and caution – field wiring.

(1)

Avoid slack connections of electrical cables

with the terminal block.

(2)

Avoid miswiring of electrical cables

connections with the terminal block.

CONNECTING ELECTRICAL WIRING TO OUTDOOR UNIT

To indoor unit Power supply

18-5 CONNECTING ELECTRICAL WIRING TO INDOOR UNIT

connect electrical cables to the terminal block of indoor unit as per the wiring diagram

and caution – field wiring.

(1) Avoid slack connections of electrical cables with the terminal block.
(2)

Avoid miswiring of electrical cables connections with the terminal block.

Lift the front panel up

Remove the plastic cover of the
electrical box loosing the screw
as shown.

CONNECTING ELECTRICAL WIRING TO INDOOR UNIT

To outdoor unit

WARNING

!

WARNING

!

Front panel

Electrical box cover

«
...
41
42
43
44
45
...
»

Содержание Creat-ion 38KHET30-708F























































Отзывы:

Нет отзывов