Carrier C708 Скачать руководство пользователя

Страница: 56 / 148

Systems, Controls and Operations

Models C708/C709/C716/C717

COMP LABEL

DESCRIPTION

FUNCTION

BASIC OPERATING LOGIC

INPUT /

OUTPUT

EPR

Inlet Pressure Upstream
Regulator

Limits the minimum
refrigerant pressure in the
hopper (currently set to 60
psig).

Limiting the minimum
refrigerant pressure in the
hopper prevents freezing of
product mix on the hopper
wall.

OPR

Outlet Pressure Downstream
Regulator

Limits the maximum pressure
in the compressor inlet
(currently set to 40 psig).

Limiting the inlet pressure to
the compressor helps
prevent overloading of the
compressor.

LIV

Liquid Injection Valve

Controls the injection of liquid
refrigerant into the suction
line.

Liquid refrigerant is injected
into the suction line to lower
the discharge temperature of
the compressor during the
cooling phase of the Heat
mode.

DBV

Hot gas discharge bypass
valve. This is an AXV valve.

Allows refrigerant to short
circuit – essentially cutting
the capacity of the
compressor when the hopper
alone is being cooled.

Refrigerant is passed
through this valve when the
hopper alone is being cooled.

Filter/Dryer

This keeps moisture, dirt,
metal, and chips from
entering the refrigerant flow
control valves.

Heat
Exchanger
(sub cooler)

This allows the liquid
refrigerant to be cooled
before it reaches the AXV
and TXV.

When the liquid is subcooled
before it reaches the
refrigerant control, the
refrigeration effect per unit
mass of refrigerant is
increased.

Receiver

The liquid receiver is a
storage tank for liquid
refrigerant.

The use of a liquid reciever
makes the quantity of
refrigerant in a system less
critical.

Содержание C708





















































































































































Результаты поиска

Содержание C708

Отзывы:

Похожие инструкции для C708

Бренды по названию

Популярные бренды

Carrier C708, Руководство по обслуживанию

Результаты поиска

Содержание C708

Отзывы:

Похожие инструкции для C708

Бренды по названию

Популярные бренды