Carrier C708 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 148

background image

14

Introduction

Models C708/C709/C716/C717

Power Switch

When placed in the ON position, the power switch
allows control panel operation.

Fluorescent Display

The fluorescent display is located on the front
control panel. During normal operation the display is
blank. The display is used to show menu options
and notifies the operator if a fault is detected. On
International models, the display will indicate the
temperature of the mix in each hopper.

Indicator Lights

MIX LOW

- When the MIX LOW symbol is

illuminated, the mix hopper has a low supply of mix
and should be refilled as soon as possible.

MIX OUT

- When the MIX OUT symbol is

illuminated, the mix hopper has been almost
completely exhausted and has an insufficient supply
of mix to operate the freezer. At this time, the AUTO
mode is locked out and the freezer will be placed in
the STANDBY mode. To initiate the refrigeration
system, add mix to the mix hopper and touch the
AUTO symbol. The freezer will automatically begin
operation.

HEAT MODE

- When the HEAT MODE symbol is

illuminated, the freezer is in the process of a heat
cycle.

BRUSH CLEAN COUNTER

- When the BRUSH

CLEAN COUNTER display has counted down to “1”,
the machine must be disassembled and brush
cleaned within 24 hours.

Adjustable Draw Handle

This unit features an adjustable draw handle(s) to
provide the best portion control, giving a better,
consistent quality to your product and controlling
food costs. The draw handle should be adjusted to
provide a flow rate of 5 to 7-1/2 oz (142 to 213 g) of
product by weight per 10 seconds. To INCREASE
the flow rate, turn the screw CLOCKWISE, and
COUNTERCLOCKWISE to DECREASE the flow
rate. (See Figure 12.)

+

-

10354

Figure 12

Beater Motor Overload

C708/C709:

The beater motor overload is located in

the service panel on the left side.

C716/C717:

The beater motor overloads are located

in the rear panel.

The overload protects the beater motor from an
overload condition. Should an overload occur, the
reset mechanism will trip. To properly reset the
freezer, place the power switch in the OFF position.
Press the reset button firmly. Turn the power switch
to the ON position. Touch the WASH symbol and
observe the freezer’s performance.

WARNING: Do not use metal objects to

press the reset button.

Failure to comply may result

in severe personal injury or death from electrical

shock.

If the beater motor is turning properly, touch the
WASH symbol to cancel the cycle. Touch the AUTO
symbol to resume normal operation. If the freezer
shuts down again, contact your authorized service
technician.

«
...
18
19
20
21
22
...
»

Содержание C708





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для C708

Бренд: WINIA Страницы: 52

Бренд: Omcan Страницы: 16

Бренд: U-Line Страницы: 46

Бренд: ZALMAN Страницы: 9

Electro-Freeze Genesis Series

Бренд: H.C Duke & Son Страницы: 96

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды